Two kg of water exist initially as a vapor and liquid at 90°C in a rigid...

Two kg of water exist initially as a vapor and liquid at 90°C in a rigid container of volume 2.42 m3.
(a)At what pressure is the system?
(b)What is the quality of the system?
(c)The temperature of the container is raised to 100°C. What is the quality of the system, and what is the pressure? What are ΔH and ΔU at this point relative to the initial state?
(d)As the temperature is increased, at what temperature and pressure does the container contain only saturated vapor? What is ΔH and ΔU at this point relative to the initial state?
(e)Make a qualitative sketch of parts (a) through (d) on a P-V diagram, showing the phase envelope.

Solutions

Expert Solution

queen_honey_blossom answered 1 year ago

Next > < Previous

Related Solutions

2 kg of water exist initially as a vapor and liquid at 90 degrees C in...

2 kg of water exist initially as a vapor and liquid at 90 degrees C in a rigid container of volume 2.42 m^3 (a) at what pressure is the system? (b) what is the quality of the system (c) the temperature of the container is raised to 100 degrees C. what is the quality of the system and what is the pressure? what are the dH and dU at this point relative to the initial state? (d) as the temperature...

A rigid 10-L vessel initially contains a mixture of liquid water and vapor at 100C with...

A rigid 10-L vessel initially contains a mixture of liquid water and vapor at 100C with 12.3 percent quality. The mixture is then heated until its temperature is 180C. Calculate the heat transfer required for this process.

A closed, rigid tank contains a two-phase liquid–vapor mixture of Refrigerant 22 initially at -20°C with...

A closed, rigid tank contains a two-phase liquid–vapor mixture of Refrigerant 22 initially at -20°C with a quality of 47.50%. Energy transfer by heat into the tank occurs until the refrigerant is at a final pressure of 6 bar. a) Determine the final temperature, in °C. b) If the final state is in the superheated vapor region, at what temperature, in °C, does the tank contain only saturated vapor?

An adiabatic tank contains 120 kg of liquid water initially at 70 °C. The water within...

An adiabatic tank contains 120 kg of liquid water initially at 70 °C. The water within the tank is utilized to quench (cool) a 15 kg steel block initially at 300 °C. The steel block is dropped into the tank, and after some time the steel block and the water in the tank reach thermal equilibrium. Determine the total entropy change during the quenching process. Specific heat of steel : Csteel= 0.50 kJ/kg*K. Specific heat of water : Cwater= 4.18...

A rigid 0.1 m3 container holds 1 kg of water, initially at 25?C. Calculate the theoretical...

A rigid 0.1 m3 container holds 1 kg of water, initially at 25?C. Calculate the theoretical minimum work required to increase the water temperature to the point where the water exists as a single phase. The environment temperature is 25?C.

A mass of 5 kg of saturated liquid vapor mixture of water is contained in a...

A mass of 5 kg of saturated liquid vapor mixture of water is contained in a piston cylinder device at 100 kPa, initially 2 kg of water is in the liquid phase and the rest is in the vapor phase.Heat is now transferred to the water and the piston which is resting on a set of stops, starts moving when the pressure in side reaches 200 kPa, heat transfer continues until the total volume increases by 20%, determine a. the...

A vessel initially contains 5.0 kg of liquid water and 2.0 kg of ice at 0...

A vessel initially contains 5.0 kg of liquid water and 2.0 kg of ice at 0 C. Energy is added until the ice has just melted. The temperature at the boundary where heat transfer occurs is taken to be the system temperature during the process. The enthalpy of melting ice is 333.5 kJ/kg. Consider the following processes used to melt the ice. a.) Heat is added to from the environment at 20 C. Determine the entropy flux and the total...

5 kg of saturated water mixture in a rigid container initially at the standard pressure (state...

5 kg of saturated water mixture in a rigid container initially at the standard pressure (state 1) is heated at constant volumeto a pressure of 35 MPa (state 2). This heating is performed in such a way that the process passes through the critical point of the water: a) What is the volume in m3 occupied by the vapor phase and the liquid phase of the mixture at the initial condition (state 1)? b) Determine the change in internal energy...

A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder...

A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 175 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. An electrical heater is in operation, and the piston rises until it hits a set of stops, which are set at double the initial volume. Electrical heating continues until the pressure reaches 500 kPa. Determine (a) the initial and final temperatures,...

A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder...

Subjects