A) A company that manufactures oil seals found the population mean to be 49.15 mm (1.935...

A) A company that manufactures oil seals found the population mean to be 49.15 mm (1.935 in.), the pop- ulation standard deviation to be 0.51 mm (0.020 in.), and the data to be normally distributed. If the internal diameter of the seal is below the lower specification limit of 47.80 mm, the part is reworked. However, if it is above the upper specification limit of 49.80 mm, the seal is scrapped.

(a) What percentage of the seals is reworked? What percentage is scrapped?

(b) For various reasons, the process average is changed to 48.50 mm. With this new mean or process center, what percentage of the seals is reworked? What percentage is scrapped? If rework is economically feasible, is the change in the process center a wise decision?

Expert Solution

orchestra answered 1 year ago

A company manufacturing oil seals wants to establish x and R control charts on the process....

A company manufacturing oil seals wants to establish x and R control charts on the process. There are 25 preliminary samples of size 5 on the internal diameter of the seal. The summary data (in mm) are as follows: 6.1. A manufacturer of components for automobile transmissions wants to use control charts to monitor a process producing a shaft. The resulting data from 20 samples of 4 shaft diameters that have been measured are: 20 ∑ xi = 10.275, i=1...

A company manufactures rods whose diameters are normally distributed with a mean of 5 mm and...

A company manufactures rods whose diameters are normally distributed with a mean of 5 mm and a standard deviation of 0.05 mm. It also drills holes to receive the rods and the diameters of these holes are normally distributed with a mean of 5.2 mm and a standard deviation of 0.07 mm. The rods are allocated to the holes at random. What proportion of rods will fit into the holes?

In a single population of locusts, the mean wing length is 47 mm, the selection gradient...

In a single population of locusts, the mean wing length is 47 mm, the selection gradient on wing length is ? = 0.12/mm, the phenotypic variance for wing length is P = 3.6 mm2, and the heritability of wing length is h2 = 0.27. In addition, we know that the additive genetic covariance between wing and leg length is 0.60 mm2. a) What is the expected evolutionary change in mean leg length due to selection on wings? b) What is...

A particular fish population has a mean length of 230 mm and a standard deviation of...

A particular fish population has a mean length of 230 mm and a standard deviation of 50 mm. What is the probability that a random sample of 16 fish from this population has a mean length of at least 240 mm?

in an oil factory, a pipe (roughness = 0.85 mm & diameter 160 mm) carries a...

in an oil factory, a pipe (roughness = 0.85 mm & diameter 160 mm) carries a fluid (specific gravity of 0.95 & viscosity 0.0061 N.s/m2) at a rate of 109. L/s. Determine; a. Flow is laminar or turbulent b. Friction factor f using explicit equation of Laminar or turbulent flow (Haaland equation) c. The head loss d. The shear stress at the pipe wall e. Velocity 30mm from the centerline f. The behavior of pipe whether fully rough, transitional, or...

An oil company wishes to construct a pressurised pipeline of 300 mm diameter to convey freshwater,...

An oil company wishes to construct a pressurised pipeline of 300 mm diameter to convey freshwater, of bulk modulus 2.10x109 N/m2 from a desalination plant to a refinery at a rate of 350 l/s and with a pipe period of 4 seconds. Calculate the corresponding theoretical surge pressure induced within the pipeline by the complete closure of an on-line valve (located at the end of the pipe) in 8 seconds. The valve generates non-uniform retardation of type R = At0.65....

A marine biologist claims that the mean length of male harbor seals is greater than the...

A marine biologist claims that the mean length of male harbor seals is greater than the mean length of female harbor seals. In a random sample of 89 male harbor seals the mean length is 132 centimeters and the standard deviation is 23 centimeters. In a random sample of 56 female harbor seals the mean length is 124 centimeters with a standard deviation of 18 centimeters. At ? = 0.05 can you support the marine biologist’s claim? Create a 90%...

Construct a 90% confidence interval for the mean length of all adult harbor seals if a...

Construct a 90% confidence interval for the mean length of all adult harbor seals if a random sample of 12 of these seals had mean length of 32 inches with standard deviation of 3 inches. Assume that the length of the seals is normally distributed.

You are employed by ABC Ltd which manufactures specialist hydraulic seals for the aircraft industry. The...

You are employed by ABC Ltd which manufactures specialist hydraulic seals for the aircraft industry. The company has developed a new seal with the following budgeted data. Variable cost per unit $ Direct materials 16 Direct labour 8 Variable overheads 8 32 The draft budget for the following years is as follows. Production and sales 120,000 units $ Fixed cost: Production 520,000 Administration 180,000 Selling, marketing and distribution 200,000 Contribution 1,680,000 Certain departmental managers within the company believe there is...

´The velocity of oil flowing thru a 30 mm diameter pipe is equal to 2m/s. Oil...

´The velocity of oil flowing thru a 30 mm diameter pipe is equal to 2m/s. Oil has a kinematic viscosity of 5 x 10 -5 sq.m/s. If the pipe has a length of 120 m, compute the Reynolds Number, friction factor, and head loss in the pipe.

Question