Question

In: Civil Engineering

´The velocity of oil flowing thru a 30 mm diameter pipe is equal to 2m/s. Oil...

´The velocity of oil flowing thru a 30 mm diameter pipe is equal to 2m/s. Oil has a kinematic viscosity of 5 x 10 -5 sq.m/s. If the pipe has a length of 120 m, compute the Reynolds Number, friction factor, and head loss in the pipe.

Solutions

Expert Solution

Solution -


Related Solutions

Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter...
Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter of 100 mm and 50 mm at the sections 1 and 2 respectively. The velocity of crude oil at the section 1 is 550 cm/s. The   section 1 is 3000 mm and section 2 is 2000 mm above the datum. If the pressure at the section 1 is 0.2 N/mm2, find the intensity of pressure at section 2?
Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are:...
Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are: Mach 3; total pressure = 1000 kPa and 550 K. The friction coefficient (f) is 0.004. The exit Mach number decreases with the length of the pipe. Assume adiabatic, steady flow. Write a short Matlab code and plot the following, while the exit Mach number changes from 2.5 to 0.99 with increments of ?M=0.01. Find the length of the pipe that is going to...
in an oil factory, a pipe (roughness = 0.85 mm & diameter 160 mm) carries a...
in an oil factory, a pipe (roughness = 0.85 mm & diameter 160 mm) carries a fluid (specific gravity of 0.95 & viscosity 0.0061 N.s/m2) at a rate of 109. L/s. Determine; a. Flow is laminar or turbulent b. Friction factor f using explicit equation of Laminar or turbulent flow (Haaland equation) c. The head loss d. The shear stress at the pipe wall e. Velocity 30mm from the centerline f. The behavior of pipe whether fully rough, transitional, or...
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water? You may ignore any minor loses.
Water in pipe AB (Figure 2), diameter (DAB) 1.2 m, is flowing with the velocity (VAB)...
Water in pipe AB (Figure 2), diameter (DAB) 1.2 m, is flowing with the velocity (VAB) of 3 m/second. Then it continues to flow through pipe BC, with a diameter (DBC) of 1.5 m and finally flows through branch pipe of CD, diameter (DCD) of 0.8 m and pipe of CE (DCE), with a velocity (VCE) of 2.1 m/second. Calculate: 1. Discharge of pipe AB (QAB) 2. Flow velocity of pipe BC (VBC) 3. Flow velocity of pipe BC (VBC)...
A 600 mm diameter pipe carrying 0.9 m3/s of oil (RD 0.85) has a 90o bend...
A 600 mm diameter pipe carrying 0.9 m3/s of oil (RD 0.85) has a 90o bend in the horizontal plane. The loss of head due to the bend is 1 metre of oil and the pressure at the start of the bend is 300kPa. Calculate the magnitude and angle of the resultant force exerted by the oil on the bend.
Fluid X is flowing in a circular pipe with a constant velocity ν (m/s). The fluid...
Fluid X is flowing in a circular pipe with a constant velocity ν (m/s). The fluid is cooled by a jacket kept at constant temperature, Tj. Fluid velocity is plug shaped , in other words uniform at radial positions. Assume that temperature is uniform in radial positions because of turbulent flow conditions; ρ and Cp of the fluid are constants. The inlet temperature (at z=0) is constant and uniform at To (To>Tj). Assume that thermal conduction of heat along the...
A 30 m long pipe with an outside diameter of 75 mm is used to deliver...
A 30 m long pipe with an outside diameter of 75 mm is used to deliver steam at a rate of 2000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be given insulation with thermal conductivity of 0.2 W / (m K) so that the vapor quality only slightly decreases to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore...
A siphon consisting of a pipe of 15cm diameter is used to empty kerosene oil (s...
A siphon consisting of a pipe of 15cm diameter is used to empty kerosene oil (s = 0.8) from a tank A. The siphon discharges to the atmosphere at an elevation of 1m. the oil surface in the tank is at ana elevation of 4m. The centerline of the siphon pipe at its highest point C is at an elevation of 5.5m. The losses in the pipe are 0.5m up to the summit and 1.2m from the summit to the...
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller...
) A 50 mm-diameter propeller was installed in a 150 mm-diameter water pipe and the propeller speed was measured for a range of water discharge in the pipe. The water had a density and dynamic viscosity of 1000 kg/m3 and 0.00112 Ns/m2 respectively. The measured results were as follows: Q (litres/s): 12 28 45 63 95 120 160 180 N (rps): 5 10 15 20 30 40 60 80 Plot the dependence of propeller coefficient against propeller Reynolds number. A...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT