Question

In: Chemistry

For a Schiff’s base condensation reaction using copper (II) acetate, salicaldehyde in methanol along with methylamine...

For a Schiff’s base condensation reaction using copper (II) acetate, salicaldehyde in methanol along with methylamine (5.2 ml, 33% in ethanol) should you/should you not use anhydrous sodium acetate? Why/why not?

Solutions

Expert Solution

Anhydrous sodium acetate which is used as a source of sodium ions in solutions. copper (II) acetate act as oxidizing agent in organic chemistry and methanol is the solvent here. For Schiff’s base condensation we need an aldehyde and an amine along with solvent and another catalyst if required but in this case, there is no use of anhydrous sodium acetate. Because as I told that anhydrous sodium acetate which is used as a source of sodium ions in solutions or you can say it disassociates in water to form sodium ions (Na+) and acetate ions but here we don't require Na+ so one can avoid using this.


Related Solutions

What compound is formed when salicaldehyde is mixed with methylamine in a Schiff’s base condensation reaction?
What compound is formed when salicaldehyde is mixed with methylamine in a Schiff’s base condensation reaction?
1) The molar solubility of copper(II) sulfide in a 0.266 M copper(II) acetate solution is _______ M.
1) The molar solubility of copper(II) sulfide in a 0.266 M copper(II) acetate solution is _______ M. 2) The maximum amount of cobalt(II) carbonate that will dissolve in a 0.258 M cobalt(II) nitrate solution is _______  M.
Verdigris, copper (II) acetate monohydrate, was prepared using the three reactions shown below. In a 125...
Verdigris, copper (II) acetate monohydrate, was prepared using the three reactions shown below. In a 125 mL Erlenmeyer flask were combined 4.20 g copper (II) sulfate pentahydrate, 35 mL of a 3.0 M aqueous solution of ammonia, and 25 mL of water (density 0.997 g/mL). The light blue solid CuSO4·3Cu(OH)2 that formed was collected by vacuum filtration and combined with 40. mL of water and 8.5 mL of a 2.0 M aqueous solution of sodium hydroxide in a second 125...
In the reaction of copper with potassium permanganate and sulfuric acid, the products are copper (II)...
In the reaction of copper with potassium permanganate and sulfuric acid, the products are copper (II) sulfate, potassium sulfate, water, and manganese (II) sulfate. First, write a balanced net ionic equation for this reaction. Then consider the reaction taking place with 100 grams of copper, 100 grams of potassium permanganate, and 400 grams of sulfuric acid. How many grams of manganese (II) sulfate could be produced in this reaction?
Adol condensation 1. What is the function of the strong base like NaOH in this reaction...
Adol condensation 1. What is the function of the strong base like NaOH in this reaction to purify solid compounds? 2. What is the purpose of recrystallization? Briefly describe the procedure of recrystallization. Explain why you added hot ethanol and then cool the solution to obtain crystals? 3. What is the name of the compound you prepared from 3-nitrobenzaldehyde and acetophenone? 4. Your melting point matched up with the pure trans chalcone product. Why did you only obtain the trans...
what is the molecular, ionic, net ionic for : 1) copper ii acetate + hydrosulfuric acid...
what is the molecular, ionic, net ionic for : 1) copper ii acetate + hydrosulfuric acid 2) copper ii sulfate + hydrosulfuric acid 3) sulfuric acid + barium hydroxide state state designations (l, s, aq, g etc)
The copper(II) chloride and aluminum reaction. calculate the kilojoules of heat produced by the reaction, assuming...
The copper(II) chloride and aluminum reaction. calculate the kilojoules of heat produced by the reaction, assuming that no energy left the calorimeter. The specific heat of the solution is 3.96J/gC ( include the mass of the aluminum foil in the total mass of the solution. Data: Trial 1 Trial2 mass of calorimeter: 8.473g 8.610g mass of solid Cucl2*2H2O: 3.232g 3.236g mass of copper solution: 64.594g 62.637g mass of aluminum foil: 0.814g 0.807g initial temperature: 19.6C 20.8C final temperature: 49.2C 53.4C
In the reaction of copper(II) sulfate with iron, what species is oxidized?             CuSO4 (aq) +...
In the reaction of copper(II) sulfate with iron, what species is oxidized?             CuSO4 (aq) + Fe (s) →→ Cu (s) + FeSO4 (aq) a. Cu2+ in CuSO4 b. Fe (s) c. Cu (s) d. Fe2+ in FeSO4 In the reaction of copper(II) sulfate with iron, what species is the oxidizing agent?             CuSO4 (aq) + Fe (s) →→ Cu (s) + FeSO4 (aq) a. CuSO4 b. Fe (s) c. Cu (s) d. FeSO4
A solution contains 1.12×10-2 M copper(II) nitrate and 9.22×10-3 M nickel(II) acetate. Solid potassium hydroxide is...
A solution contains 1.12×10-2 M copper(II) nitrate and 9.22×10-3 M nickel(II) acetate. Solid potassium hydroxide is added slowly to this mixture. What is the concentration of copper(II) ion when nickel ion begins to precipitate? [Cu2+] =
Methanol is manufactured by the partial combustion of methane under pressure, using a copper catalyst: CH4(g)...
Methanol is manufactured by the partial combustion of methane under pressure, using a copper catalyst: CH4(g) + ½ O2(g) → CH3OH(l) Enthalpies of combustion are (in kJ mol-1): CH4(g), -881 CH3OH(l), -726 Calculate the standard enthalpy change for the manufacture of 1 mole methanol by the reaction CH4(g) + ½ O2(g) → CH3OH(l) Follow the procedures based on Hess’s Law: First write down the reactions corresponding to the enthalpies of combustion you have been given, reverse one of the equations...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT