Question 4) If the effective pressure of the water in the pipe is 3 atm and...

Question 4) If the effective pressure of the water in the pipe is 3 atm and in the case of h1 = 1m, h2 = 0.5m, h3 = 1m, h4 = 2m and h5 = 0.1m, determine the relative density of the fluid. (Accept that ρoil = 850 kg / m3, ρwater = 1000 kg / m3, ρhg = 13600 kg / m3, g = 9.81 m / s2. Neglect the pressure from the air at the height of h2.)

all informations have given

Solutions

Expert Solution

Ally Wells answered 1 year ago

Next > < Previous

Related Solutions

Question 1) As water passes from a pipe of larger diameter to a pipe of smaller...

Question 1) As water passes from a pipe of larger diameter to a pipe of smaller diameter in converging section, the static pressure: Becomes half Increases Decreases Does not change Question 2) The following reading have to be recorded from the flow measurement apparatus to calculate the mass flow rate from the venturimeter? Pressures at the inlet and exit of the venturimeter Pressures at the inlet and throat of the venturimeter The rotameter reading venturimeter The pressure at the throat...

When water boils at 100oC and 1.00 atm of pressure, is the change in entropy of...

When water boils at 100oC and 1.00 atm of pressure, is the change in entropy of the surroundings/environment negative, zero, or positive?

Water at a pressure of 7 atm at street level flows into a tall building at...

Water at a pressure of 7 atm at street level flows into a tall building at 1.5 m/s through a 6 cm diameter pipe. The pipe tapers down to 2 cm on the top floor, 60 m from the ground. What is the pressure in the faucet on the top floor? A. 23.2 kPa B. 28.4 kPa C. 31.1 kPa D. 33.6 kPa

A water is in equilibrium with CO2 in the atmosphere (partial pressure is 3.16 .10‾⁴atm) and...

A water is in equilibrium with CO2 in the atmosphere (partial pressure is 3.16 .10‾⁴atm) and with CaCO3(s). The pH is 8.1. Ignoring Ca complexes, what is the solubility (S) of Ca?

Water at a gauge pressure of P P = 3.2 atm a t m at street...

Water at a gauge pressure of P P = 3.2 atm a t m at street level flows into an office building at a speed of 0.78 m/s m / s through a pipe 5.8 cm c m in diameter. The pipe tapers down to 2.2 cm c m in diameter by the top floor, 16 m m above (Figure 1). Assume no branch pipes and ignore viscosity. Figure1 of 1 Part A Calculate the flow velocity in the pipe...

10. Water at a pressure of 3.60 atm at street level flows into an office building...

10. Water at a pressure of 3.60 atm at street level flows into an office building at a speed of 0.60 m/s through a pipe 4.40 cm in diameter. The pipes taper down to 1.50 cm in diameter by the top floor, 23.0 m above. Calculate the water pressure in such a pipe on the top floor.

Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105...

Water moves through a constricted pipe in steady, ideal flow. The pressure is 1.80 ✕ 105 Pa and the pipe radius is 2.90 cm. At the higher point located at y = 2.50 m, the pressure is 1.30 ✕ 105 Pa and the pipe radius is 1.60 cm. (a) Find the speed of flow in the lower section. m/s (b) Find the speed of flow in the upper section. m/s (c) Find the volume flow rate through the pipe. m3/s

Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of...

Water flowing along a horizontal pipe has a speed of 2.31 m/s and a pressure of 4.25 atm. Further along, the pipe narrows so that the cross-sectional area decreases by a factor of 6.17. What is the pressure in the narrow section?

A mixture of gases collected over water at 14oC has a total pressure of 1.198 atm...

A mixture of gases collected over water at 14oC has a total pressure of 1.198 atm and occupies 72 mL. How many grams of water escaped into the vapor phase?

Q. No 3. The pressure drop Dp over a length L of pipe is assumed to...

Q. No 3. The pressure drop Dp over a length L of pipe is assumed to depend on the average velocity V, the pipe’s diameter D ,the average height h of the roughness elements of the pipe wall, the ﬂuid density ρ ,and the ﬂuid viscosity µ .Write a relationship between the pressure drop and the other variables. Use Indicial Method (Rayleigh’s Method) only.

Subjects