if 2C6H12O6+2Ca+13O2–> 2CaCO3+10CO2+12H2O air to fuel ratio is 10 and the mass flow rate of wood...

if 2C6H12O6+2Ca+13O2–> 2CaCO3+10CO2+12H2O

air to fuel ratio is 10

and the mass flow rate of wood is 0.00026kg/s

how can i calculate the flue gas flowrate

help asap pleaseee

Expert Solution

queen_honey_blossom answered 2 years ago

Ethane (C2H6) is burned with air in a steady-flow combustor. The mass flow rate of fuel...

Ethane (C2H6) is burned with air in a steady-flow combustor. The mass flow rate of fuel entering the combustor is 0.57 kg/s and the equivalence ratio is 0.64. The fuel enters at 25oC and the air enters at 500 K. Determine: The heat release rate, in kW. The mass flow rate of air, in kg/s. The mole fraction of O2 in the products. The mass fraction of CO2 in the products. The total mass of CO2 produced per year (365...

Calculate the heat of combustion and the stoichiometric fuel to air ratio (mass and molar) for...

Calculate the heat of combustion and the stoichiometric fuel to air ratio (mass and molar) for 1) Methane and 2) Octane. Comment on whether the assumption of f<<1 is valid for these conditions.

The air mass flow rate of a jet engine is 10 kg/s. The stagnation enthalpy at...

The air mass flow rate of a jet engine is 10 kg/s. The stagnation enthalpy at the exit of the turbine is 918 kJ/kg and the excess air is 4.5. (a) What should be the mass flow rate of fuel injected in the afterburner, such that the stagnation enthalpy at the end of the afterburner is 1700 kJ/kg? (b) What is the excess air in the afterburner? (c) What is the maximum temperature in the afterburner?

Calculate air to fuel ratio by mass, for a four-cylinder SI engine running on i) gasoline...

Calculate air to fuel ratio by mass, for a four-cylinder SI engine running on i) gasoline and ii) a mixture of 20% methanol and 80% gasoline both at stoichiometric conditions. Assume gasoline is represented with C8H18 . Calculate any loss of power when gasoline-methanol mixture is used and discuss your results.

Ethane gas (C2H6) is burned with air. The fuel flow rate is 0.1 kg/s and the...

Ethane gas (C2H6) is burned with air. The fuel flow rate is 0.1 kg/s and the air flowrate is 2.2 kg/s. Ethane’s enthalpy of formation is -84,680 kJ/kmol. Determine: The equivalence ratio Ethane’s lower heating value by deriving it from enthalpy of formation data. The heat release rate, in kW. The mass fraction of oxygen in the products. The mass of CO2 emitted per 1000 hours of operation. The mass of fuel burned per 1000 hours of operation. The adiabatic...

how do you relate the air fuel ratio to the equivalence ratio, and the ‘lambda’ ratio

Why the temperature increase when flow rate of air increase in air-ch4 combustion, and equivalence ratio...

Why the temperature increase when flow rate of air increase in air-ch4 combustion, and equivalence ratio always uniforms ??

Consider the following combined cycle. The mass flow rate of air is 73 kg/s. Air enters...

Consider the following combined cycle. The mass flow rate of air is 73 kg/s. Air enters the compressor at state 1 with Patm =1 atm and Tamb = 20°C. The compressor has a pressure ratio of 7.5 and an efficiency ?c = 0.85. Air enters the combustor and is heated to a temperature TH = 1250°C. The turbine has an efficiency of ?t,1 = 0.87. The air leaving the turbine enters the steam boiler where it transfers heat to the...

(a) What is the best air/fuel ratio for an automobile engine? (b) If the mixture is...

(a) What is the best air/fuel ratio for an automobile engine? (b) If the mixture is made leaner, what happens to the hydrocarbon emissions? (c) If the fuel mixture is richer, how does this affect NOx emissions

The flow rate of warm air into the air conditioning is 5,000 cfm. An air conditioning...

The flow rate of warm air into the air conditioning is 5,000 cfm. An air conditioning system takes outdoor air at 95 degrees F dry-bulb and 70% relative humidity, and discharges it at 60 degrees F dry-bulb and 95% relative humidity. The air conditioning system operates on a vapor compression cycle using R134a between 20 and 200 psia. Refrigerant enters the compressor at 20 degrees F and leaves the compressor at 180 degrees F. Refrigerant enters the evaporator coil at...

Question