Question

In: Physics

A platform is supported by a row of aluminum pipe columns having length L of 5...

A platform is supported by a row of aluminum pipe columns having length L of 5 m and outer
diameter d of 300 mm. The bases of the columns are set in concrete footing and the tops are
supported by the platform laterally (like a hinge). The columns are being designed to support
compressive loads P of 200 kN. Determine the minimum required thickness t of the columns if a
factor of safety n = 1.5 is required with respect to Euler buckling. E = 72 GPa and ? y = 350 MPa.

Solutions

Expert Solution


Related Solutions

A 3.5-kg object is supported by an aluminum wire of length 1.8 m and diameter 2.0...
A 3.5-kg object is supported by an aluminum wire of length 1.8 m and diameter 2.0 mm . How much will the wire stretch?
A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8...
A cylindrical specimen of aluminum having a diameter of 0.75 inches and a length of 8 inches is deformed elastically in tension with a force of 11,000 lb. Assume the following properties: Modulus of Elasticity: 10 Mpsi; Yield Strength: 40 kpsi; Tensile Strenght: 50 kpsi; Percent Elongation: 17; Poisson's Ratio: .33 Determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress (b) The change in diameter of the specimen. Will the...
Q. No 3. The pressure drop Dp over a length L of pipe is assumed to...
Q. No 3. The pressure drop Dp over a length L of pipe is assumed to depend on the average velocity V, the pipe’s diameter D ,the average height h of the roughness elements of the pipe wall, the fluid density ρ ,and the fluid viscosity µ .Write a relationship between the pressure drop and the other variables. Use Indicial Method (Rayleigh’s Method) only.
A cylindrical aluminum pipe of length 1.42 m has an inner radius of 1.60 ×10-3 m...
A cylindrical aluminum pipe of length 1.42 m has an inner radius of 1.60 ×10-3 m and an outer radius of 3.39 ×10-3 m. The interior of the pipe is completely filled with copper. What is the resistance of this unit? (Hint: Imagine that the pipe is connected between the terminals of a battery and decide whether the aluminum and copper parts of the pipe are in series or in parallel.)
A uniform horizontal 50.0 kg beam of length l= 3.50 m is at rest, supported by...
A uniform horizontal 50.0 kg beam of length l= 3.50 m is at rest, supported by a vertical rope located d =0.850 m from its left end . The right end of the beam is supported by a column which exerts an upward force on the beam a) Draw an exteded force diagram of the beam b) solve for (i) the magnitude of the tension in the rope and (ii) the force that the column exerts on the beam.
Consider a simply supported beam of length L. The beam experiences a parabolically varying distributed load...
Consider a simply supported beam of length L. The beam experiences a parabolically varying distributed load that varies from 0 at the left support, to a maximum w at midspan, and back to 0 at the right support. The beam has stiffness properties EI. Give a mathematical equation that gives the value of the distributed load intensity at any distance z along the beam in terms of w, L and z. Draw the SFD and BMD of the beam, giving...
1. A rod of uniform density and weight W=120N has length L=1.00 m and is supported...
1. A rod of uniform density and weight W=120N has length L=1.00 m and is supported at two points, under the 10 cm point and under the 70 cm point. The support at 10 cm exerts a force NL on the rod and the support at 70 cm exerts a force NR on the rod, both forces being in the vertical direction. (a) Use the conditions of static equilibrium to find the values of NL and NR. (b) In order...
A constant pitch helical coil is made from a length L=7m of round conductor having a...
A constant pitch helical coil is made from a length L=7m of round conductor having a copper core with diameter d=0.1mm and covered with an insulation of thickness t=0.02m, by winding the conductor on a mandrel having a length Lm=120mm and a diameter dm=3mm and allowing equal leads for connection at the two ends, each with a length l=10mm Calculate the coil DC resistance if the electrical resistivity of copper is 1.72 µΩcm [marks 2] Calculate the coil inductance [marks...
Wood beam Question. A simply supported #1 DF-L (Douglas Fir-Larch) beam 8 foot in length has...
Wood beam Question. A simply supported #1 DF-L (Douglas Fir-Larch) beam 8 foot in length has a point load of 2K at mid span. The beam is 4 x 8 in the strong axis orientation, and is fully braced, the moisture content is less than 19% and the max deflection is L/360. (include the weight of the beam in your calculations) Find the Tabulated stresses. Find the Allowable stresses Find the Actual stresses Is the member adequate. Using the same...
Pipe Diameter(D)=150mm, Pipe Length(L)=980m, Friction factor(lambda)=0.05, Water level(h)=18m (i) Neglecting minor losses plot the pipeline characteristic...
Pipe Diameter(D)=150mm, Pipe Length(L)=980m, Friction factor(lambda)=0.05, Water level(h)=18m (i) Neglecting minor losses plot the pipeline characteristic curve (system curve), for a flow rate range of 10-60 m3 /hr. (ii) For an average flow of 20 m3 /hr select a suitable pump from the pump performance charts provided. (iii) What are the discharge and head values you would record at duty point for the selected pump?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT