Question

In: Mechanical Engineering

A rectifier is to be specified for a DN 600 mm pipeline cathodic protection system. The...

A rectifier is to be specified for a DN 600 mm pipeline cathodic protection system. The current density required is 1.5 x 10-4 amps/m2. Calculate the current to be supplied by the rectifier if the cathodic protection installations are 30 km apart. POST THE SOLUTION IN NEAT READIBLE SCRIPT PLEASE!!

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is...
A long, straight horizontal pipeline of diameter 350 mm and effective roughness size 0.03 mm is to be constructed to convey crude oil of density 860 kg/m3 and absolute viscosity 0.0064 N s∕m2 from the oilfield to a port at a steady rate of 7000 m3/day. Booster pumps, each providing a total head of 20 m with an overall efficiency of 60%, are to be installed at regular intervals. Determine the required spacing of the pumps and the power consumption...
Water is flowing in a 200 mm pipeline fitted with a 45o bend in a vertical...
Water is flowing in a 200 mm pipeline fitted with a 45o bend in a vertical plane. The diameter at the outlet of the bend is 500 mm. The pipe axis at the inlet is horizontal and the outlet is 1.5 m above the inlet. If the flow through the bend is 0.4 m3/s and a head loss of 0.5 m occurs in the bend, calculate the magnitudes and the directions of the resultant force the bend support must withstand....
An oil company wishes to construct a pressurised pipeline of 300 mm diameter to convey freshwater,...
An oil company wishes to construct a pressurised pipeline of 300 mm diameter to convey freshwater, of bulk modulus 2.10x109 N/m2 from a desalination plant to a refinery at a rate of 350 l/s and with a pipe period of 4 seconds. Calculate the corresponding theoretical surge pressure induced within the pipeline by the complete closure of an on-line valve (located at the end of the pipe) in 8 seconds. The valve generates non-uniform retardation of type R = At0.65....
A part must be 600 mm +2 mm long to meet engineering specifications. There has been...
A part must be 600 mm +2 mm long to meet engineering specifications. There has been a chronic problem with part lengths being out of specification − a problem that has caused poor-fitting assemblies down the production line and high scrap and rework rates. You are asked to do a capability analysis for two shifts. Using Minitab run Process Capability Analysis > Normal for each shift. Shift 1 Shift 2 599.62 600.28 600.47 600.14 600.83 601.21 599.85 599.58 600.54 599.57...
At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits...
At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits snugly over a steel hoop 15 mm thick. Both hoops are 100 mm wide. Compute the contact pressure between the hoops when the temperature drops to 20°C. Neglect the possibility that the inner ring may buckle. For steel, E = 200 GPa and α = 11.7μm/(m.°C). For bronze, E = 83 GPa α = 19 μm/(m.°C)
At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits...
At 130°C, a bronze hoop 20 mm thick whose inside diameter is 600 mm just fits snugly over a steel hoop 15 mm thick. Both hoops are 100 mm wide. Compute the contact pressure between the hoops when the temperature drops to 20°C. Neglect the possibility that the inner ring may buckle. For steel, E = 200 GPa and α = 11.7μm/(m.°C). For bronze, E = 83 GPa α = 19 μm/(m.°C) At 130°C, a bronze hoop 20 mm thick...
In the system of protection devised by the International Commission on Radiological Protection ICRP, absorbed dose...
In the system of protection devised by the International Commission on Radiological Protection ICRP, absorbed dose to organs and tissues are converted to equivalent dose and effective dose. Explain how and why this is done.
A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a...
A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a maximum total depth h= 400 mm. It = 542 kN.m. Design the umust carry a total factored load moment Mflexural reinforcement for this member, using compression steel if necessary. Allow 75 mm to the center of the bars from the compression or tension face of the beam. Material strengths are ??′=27.6 ??? ??? ??=413 ?? ?. Select reinforcement to provide the needed areas, and...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.
What effect would you expect a spectroscope with a diffraction grating of 600 lines mm to...
What effect would you expect a spectroscope with a diffraction grating of 600 lines mm to have on sharpness and resolution in your spectrum
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT