1.Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute center frequency, Wo. Calculate...

1.Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute center frequency, Wo. Calculate the cutoff frequencies Wc1 and Wc2, the bandwidth (Beta),

and quality factor, Q. Compute the values for R and L to yield a bandpass filter with a center frequency of 5kHz and a bandwidth of 200Hz, using a 10nF capacitor.

Expert Solution

Manojponduru answered 1 year ago

Design the component values for the series RLC bandreject filter so that the center frequency is...

Design the component values for the series RLC bandreject filter so that the center frequency is 5 kHz and the quality factor is 5. Use a 500 nF capacitor. Important: Please.....Plot the circuit of your design, marking the output voltage. I think it means a sinewave on an X, Y, graph plot with vo as X, and t(ms)>0 as Y. Is this possible here?

Use a 5 nF capacitor to design a series RLC bandpass filter, as shown at the...

Use a 5 nF capacitor to design a series RLC bandpass filter, as shown at the top of Fig. 14.27.The center frequency of the filter is 8 kHz, and the quality factor is 2. a) Specify the values of R and L.using pspice b) What is the lower cutoff frequency in kilohertz? using pspice c) What is the upper cutoff frequency in kilohertz?using pspice d) What is the bandwidth of the filter in kilohertz?using pspice

a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and...

a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and an upper cutoff frequency of 4500 Hz. The passband gain of the filter is 20 dB. The gain should be down at least 15 dB at 200 Hz and 11.25 kHz. Use 20 nF capacitors in the high-pass circuit and 10 k\Omega resistors in the low-pass circuit. b) Draw a circuit diagram of the filter and label all the components.

Part 5 The frequency response of RLC circuits : Design a passive filter: Band Pass, ISM...

Part 5 The frequency response of RLC circuits : Design a passive filter: Band Pass, ISM Band 433.050 MHz to 434.790 MHz . Prepare a report to describe your design. Your results should include the following : i. Simulation of the designed filters by using any simulation software. ii. Attach a 1 kΩ resistor as a load to the initial design of your filter. Explain how the transfer function change. Does the type of filter change? Does the cut-off frequency...

1. Determine the ROC for stability for transfer function H(s) = 1 / (s-2) ( s-1)...

1. Determine the ROC for stability for transfer function H(s) = 1 / (s-2) ( s-1) 2. Determine the ROC for stability for transfer function H(z) = (z-1) / (z+0.1) (z-0.2)

1, Sketch a second order LC filter, determine the transfer function and the cut-off frequency 2,...

1, Sketch a second order LC filter, determine the transfer function and the cut-off frequency 2, Explain the 6 classification of filters

For the system with transfer function H(s)=1/(s-2)(s-1) determine the ROC for stability.

Design a four-pole Chebychev bandpass filter which a passband of 4750 rads/sec to 5250 rad/s. The...

Design a four-pole Chebychev bandpass filter which a passband of 4750 rads/sec to 5250 rad/s. The pass band must have a magnitude between -0.5 and 0 db..

Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and...

Design a bandstop filter with a cutoff frequency of -3dB at W1 = 100 rad/s and W2 = 10,000rad/s. Confirm by plotting the magnitude and phase of the transfer function in matlab.

Consider a system with the following transfer function, G(s) = 10/ [s(s + 1)]. Design a...

Consider a system with the following transfer function, G(s) = 10/ [s(s + 1)]. Design a compensator according to the following design objectives: • Kv = 20 sec−1 ; • PM = 50 oF; • GM ≥ 10 dB. Submit your answer regarding the detailed compensator design procedures, and the corresponding MATLAB code and figures to verify your design. In addition, compare the step response of both uncompensated and compensated systems in MATLAB

Question