A 1.5-in-diameter bar has been machined from an AISI 1050 cold-drawn bar. This part is to...

A 1.5-in-diameter bar has been machined from an AISI 1050 cold-drawn bar. This part is to withstand a fluctuating tensile load varying from 0 to 62 kip. Because of the ends, and the fillet radius, a fatigue stress-concentration factor Kf is 1.85 for 106 or larger life. Estimate the fatigue factor of safety based on achieving infinite life (use Modified Goodman criteria) and the yielding factor of safety. If infinite life is not predicted, estimate the number of cycles to failure (use Modified Goodman criteria).

Expert Solution

Thank you...

samet mamat answered 2 years ago

For AISI 1050 Steel at 10 cm in diameter, use case hardening methods to produce a...

For AISI 1050 Steel at 10 cm in diameter, use case hardening methods to produce a surface hardness of at least 60 HRC. Describe the method that will create a thin, carbon enriched surface layer in order to maintain the ductile properties of the core. Show calculations.

The process that produces a machined part has a normal distribution with the average diameter of...

The process that produces a machined part has a normal distribution with the average diameter of 7.2 cm and a standard deviation of 0.35 cm. What is the probability that a part will have a diameter between 7.1 cm and 7.6 cm? Select one: a. 0.4859 b. 0.8734 c. 0.3875 d. 0.2609

determine the cutting speed and calculate spindle RPM for driiling a 1.5" diameter hole ins AISI-SAE...

determine the cutting speed and calculate spindle RPM for driiling a 1.5" diameter hole ins AISI-SAE 1020 steel with a brinell hardness of 125 to 175

A 70% Cu–30% Zn brass wire is cold-drawn 15 percent to a diameter of 4.53 mm....

A 70% Cu–30% Zn brass wire is cold-drawn 15 percent to a diameter of 4.53 mm. The wire is then further cold-drawn to a diameter of 3.98 mm. (a) Calculate the total percent cold work that the wire undergoes. (b) Estimate the wire’s tensile and yield strengths and elongation from Fig. 6.44.

A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter...

A stainless steel (AISI 316) tube used to transport a chilled pharmaceutical has an inner diameter of 30 mm and a wall thickness of 3 mm. The pharmaceutical and ambient air are at temperatures of 6oC and 23oC, respectively, while the corresponding inner and outer convection coefficients are 400 W/m2 K and 6 W/m2 K, respectively. (a) What is the heat gain per unit tube length? (b) What is the heat gain per unit length if a 10-mm thick layer...

What is the speed of an electron that has been accelerated from rest through a potential difference of 1050?

A series of 20 samples of size 4 has been drawn from a project. The measure...

A series of 20 samples of size 4 has been drawn from a project. The measure of interest has an average of 20.0443, and the average range within the samples is 0.0567. Determine the control chart lower limit for x-bar" "A series of 20 samples of size 4 has been drawn from a project. The measure of interest has an average of 20.0443, and the average range within the samples is 0.0567. Determine the control chart upper limit for R"...

A pure aluminum bar has a diameter of 15 cm and a length of 1.25 m....

A pure aluminum bar has a diameter of 15 cm and a length of 1.25 m. The rod is initially uniform in temperature at 300?C. The bar is now suddenly exposed to a convection environment at 50?C with h = 1250 W/m K. How long does it take the center to cool to a temperature of 80?C? (a) Determine if a lumped capacitance analysis is or is not appropriate. (b) Determine the cooling time assuming the lumped capacitance model is...

A volume of 1.5 L of air at 36°C is expelled from the lungs into cold surroundings at 6.4°C.

A volume of 1.5 L of air at 36°C is expelled from the lungs into cold surroundings at 6.4°C. What volume does the expelled air occupy at this temperature? The pressure and the number of gas particles do not change.

Saturated water vapor has a flow rate of 1.5 kg/s and a pressure of 0.51 bar....

Saturated water vapor has a flow rate of 1.5 kg/s and a pressure of 0.51 bar. The vapor is to be completely condensed to saturated liquid in the shell of a shell-and-tube heat exchanger. In this case, the water vapor enters and the water exits at the same temperature, which represents a case with infinitely high m_dot * Cp for this condensing steam application. On the tube side, city water is used as the cold fluid. The city water enters...

Question