Question

In: Physics

Please Show Work 1. A hydraulic motor provides torque to a load through a shaft turning...

Please Show Work

1. A hydraulic motor provides torque to a load through a shaft turning at 632 rev/min. The motor has 29 gal/min of fluid going through it, and the pressure at the motor inlet is 2,191 psi. What torque (in ft-lb) is the motor providing? (Assume 100 % efficiency).

2. Fluid is flowing at a velocity of 2 ft/s in a 0.6 in. ID pipe. The pipe transitions to an ID of 3 in. What is the fluid velocity (in ft/s) in the larger pipe?

3. An automobile that weighs 8,945 N is lifted 3 m in 10 s. How much power was delivered to the car (in kW)?

4. A liquid fuel stores energy chemically. The higher heating value (HHV) of a fuel is the energy stored in a fuel per unit of mass. For gasoline, the HHV is 47,600 kJ/kg. If the density of gasoline is 0.735 kg/L, how many joules of energy are in a gallon?

Solutions

Expert Solution


Related Solutions

Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load....
Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load. shaft rotates 800 rpm and its roller bearing has lh=10000 hours working life.Choose the single row roller bearing .(define the diameter of shaft)(Can you assign it to the table pictures.)
An electric motor exerts a constant torque of τ=10N⋅m on a grindstone mounted on its shaft;...
An electric motor exerts a constant torque of τ=10N⋅m on a grindstone mounted on its shaft; the moment of inertia of the grindstone is I=2.0kg⋅m2. If the system starts from rest, find the work done by the motor in 8.0 s and the kinetic energy at the end of this time. What was the average power delivered by the motor? Part A:Suppose we now turn off the motor and apply a brake to bring the grindstone from its greatest angular...
A 240 V DC shunt motor draws 40 A while driving a constant torque load. The...
A 240 V DC shunt motor draws 40 A while driving a constant torque load. The armature resistance is Ra = 0.2 Ω, the field resistance is Rf = 240 Ω and machine constant is Ka = 120. The part of magnetization characteristic (field flux versus field current) related to the question is: If (A) :      0.70 0.80 0.86 0.90 1.00 1.10 1.20 1.30 1.40 ϕ (mWb) : 5.80 6.30 6.59 6.70 7.20 7.60 7.96 8.20 8.45 The constant rotational...
Motor sizing decision must consider 3 factors; stall torque, no load speed and maximum power. With...
Motor sizing decision must consider 3 factors; stall torque, no load speed and maximum power. With the help of motor performance chart, please discuss them in detail.
True or False: 1. Keys are used to enable transmission of torque from the shaft to...
True or False: 1. Keys are used to enable transmission of torque from the shaft to the shaft supported elements. 2. For the same bore diameter, a cylindrical roller bearing generally has a lower load carrying capacity than ball bearings. 3. Thrust bearings are suitable for supporting both axial and radial loads. 4. Typical bearing failures are due to excessive static stresses. 5. According to the seminar presentations, materials for joint replacements are selected on basis of the loading as...
A 6-pole, 50 Hz, 3-phase induction motor running on full load develops a useful torque of...
A 6-pole, 50 Hz, 3-phase induction motor running on full load develops a useful torque of 160 Nm when the rotor emf makes 120 complete cycles per minute. The windage and friction loss is 1005.30 Watt. It is assumed; the core loss is lumped together with the windage and friction loss. The total stator loss is given to be 800 Watt. Compute: a) Shaft power output, b) The copper loss in the rotor winding,c) The input power to the motor, and d) The...
How does the “World’s Simplest Motor” work? Describe the torque due to the magnetic field on...
How does the “World’s Simplest Motor” work? Describe the torque due to the magnetic field on the wire loop as it turns. Explain why it is necessary to ensure only one side of the wire is scraped of enamel to make electrical contact. 
Show your work please Below are the results of a study. Through the sample of the...
Show your work please Below are the results of a study. Through the sample of the first 49 Super Bowls, 28 of them were won by teams in the National Football Conference (NFC). A 0.1% (1/10 of 1%) significance level was used to test the claim that the probability of an NFC team Super Bowl win is greater than one-half. Confirm the results with a confidence interval. a) What is the range of the confidence interval? b) Does the confidence...
(Answers are given but could you please work through the problem and show me the steps?)...
(Answers are given but could you please work through the problem and show me the steps?) Chapter 8 A local health center noted that in a sample of 400 patients, 80 were referred to them by the local hospital. a. Provide a 95% confidence interval for all the patients who are referred to the health center by the hospital. b. What sample size would be required to estimate the proportion of all hospital referrals to the health center with a...
(Answers are given but can you please work through the problem and show the steps) Chapter...
(Answers are given but can you please work through the problem and show the steps) Chapter 10 p2 Allied Corporation is trying to determine whether to purchase Machine A or B. It has leased the two machines for a month. A random sample of 5 employees has been taken. These employees have gone through a training session on both machines. Below you are given information on their productivity rate on both machines. (Let the difference d = Machine A -...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT