Question

In: Electrical Engineering

I need to model a series RLC circuit with a AC voltage source using simulink which...

I need to model a series RLC circuit with a AC voltage source using simulink which measures current and voltage across each component. Please include the formulas your model is based off of. thanks.

R = 1ohm
L = 1 millhenery
C = 1 microfarad

Expert Solution

Below is the simulonk model with Rms voltage and current across R,L and C displayed in the model. The waveforms are also attached subsequently.

Below is snapshot for one of the multimeters. You will get the list of measurement in each multimeter after you select the parameter to be measured from the R,L and C block respectively. You need to select them at each multimeter to get the rms value displayed.

Manual calculations attached below.

In case you have any doubt feel free to ask your doubt in the comments section.I would be happy to clarify it.

DO GIVE A THUMBS UP!!

Manojponduru answered 1 year ago

An RLC circuit consists of an AC voltage source with a maximum voltage of 122 Volts...

An RLC circuit consists of an AC voltage source with a maximum voltage of 122 Volts connected in series to a resistor, a capacitor, and an inductor. At the resonant frequency, the inductive reactance is 13 Ohms and the total impedance of the circuit is 23 Ohms. What is the average power produced by the battery at 2.6 times the resonant frequency in Watts?

An RLC circuit consists of an AC voltage source with a maximum voltage of 135 Volts...

An RLC circuit consists of an AC voltage source with a maximum voltage of 135 Volts connected in series to a resistor, a capacitor, and an inductor. At the resonant frequency, the inductive reactance is 15 Ohms and the total impedance of the circuit is 24 Ohms. What is the average power produced by the battery at 2.6 times the resonant frequency in Watts?

Develop a series RLC circuit that increases the capacitor voltage to the source voltage as fast...

Develop a series RLC circuit that increases the capacitor voltage to the source voltage as fast as possible with no more than a 20% overshoot. The source voltage is 99V, the capacitance is 9F the and the inductance is 23 H. You can adjust the resistance since that the inductance are the two easiest parameters to adjust. I suggest you find ω0 for your circuit and the value of R that results in a critically damped circuit. Plot this vs....

A series ac circuit consists of a voltage source of frequency f = 60 Hz and...

A series ac circuit consists of a voltage source of frequency f = 60 Hz and source voltage amplitude 345 volts, a resistor of resistance R = 255 Ω, a capacitor of capacitance C = 6.2×10−6F, and an inductor of inductance L. (a) What must be the value of L for the phase angle Φ to be zero? (b) When L has the value calculated in (a), what is the current amplitude in the circuit?

A series RLC circuit connected to a 24-V AC source has a current of 150 mA...

A series RLC circuit connected to a 24-V AC source has a current of 150 mA when the AC source is set to 85 Hz. The voltage on the capacitor is measured to be 36 V. When the frequency of the source is adjusted in any way the current decreases. Calculate the values of R L, and C. In P4, the frequency of the AC source is increased until the voltage on the capacitor has dropped to 12 V. Calculate...

Consider an RLC circuit that is driven by an AC source with an adjustable frequency. Is...

Consider an RLC circuit that is driven by an AC source with an adjustable frequency. Is possible for the maximum voltage drop across the capacitor to exceed the maximum voltage? Explain in 100 words or less. I know the answer is yes, but can you explain this conceptually, not mathmatically? thanks.

A series RLC circuit is connected to a 240V AC generator that operates at 99Hz. In...

A series RLC circuit is connected to a 240V AC generator that operates at 99Hz. In the circuit, R = 4.325 kΩ and C = 0.71mF. You must have a circuit diagram, wherever necessary, to receive full credit on this question. (a) Determine the inductance, L, such that the current in the circuit is 19.1mA. (b) Using the value determined for L in part (a), determine the frequency at which the current in the circuit is maximized. What do physicists...

(Transient Current) An RLC series circuit has a voltage source given by E(t) = 20sin(t) V,...

(Transient Current) An RLC series circuit has a voltage source given by E(t) = 20sin(t) V, an inductor of 3 H, a resistor 6 Ω, and a capacitor of 1/3 F. Find the current I(t) in this circuit for t > 0 if I(0) = 2, I'(0) = 0. Find the moment of time when the transient current is equal to zero

a circuit that has a resistor, capacitor, and inductor in series with a 5V AC voltage...

a circuit that has a resistor, capacitor, and inductor in series with a 5V AC voltage source R = 5 Ω; L = 1 mH; C = 447 a) Find ω0 and f0 b) Complete the table f = f0 f = 0.5f0 f = 1.5f0 I VL Vc c) What is the phase between circuit current and applied voltage at f = f0 (in radians) d) Determine if the below statements are true or false Below resonance (f <...

10.An AC voltage source is connected in series to an inductor, a capacitor, and a resistor...

10.An AC voltage source is connected in series to an inductor, a capacitor, and a resistor of 8 Ohms. At the frequency when the phase angle is zero, capacitive reactance is 7 Ohms. What is the phase angle between the current and voltage at a frequency which is a factor of 3.2 times less than this frequency? answer in degresss and if negative 6. the resistance of a coil spun in a generator is 2 Ohms. the coil is in...