Question

In: Physics

Let's consider a rectangular wave guide with dimensions of ? = 1.58 cm and ? =...

Let's consider a rectangular wave guide with dimensions of ? = 1.58 cm and ? = 0.79 cm, filled with air inside and copper outside.

a) Calculate the cutoff frequency for the first three advancing modes. Specify the name of the

dominant (basic) mode.

b) Draw roughly the electric field and magnetic field lines in the waveguide sections (sections taken from the xy, yz and xz planes) for the basic mode. For drawing, consider that the waveguide extends in the z direction, its long edge on the x axis and its short edge on the y axis.

c) When a signal with a frequency of 7 GHz enters this waveguide,

explain its behavior by considering its propagation constant.

d) ? = number of waves (calculate for the frequency of 10 GHz.)

e) (?) phase constant (Calculate for the frequency of 10 GHz.)

f) (??) wavelength in the guide (Calculate for the frequency of 10 GHz.)

g) (??) phase speed (Calculate for the frequency of 10 GHz.)

i) Find the weakening of 1m in Np/m and dB/m. (In the calculations, you can get the surface resistance of the copper element Rs = 0.026(ohm) for 10 GHz.) (Calculate for the frequency of 10 GHz.)

Solutions

Expert Solution


Related Solutions

A closely wound rectangular coil of 80 turns has dimensions 25.0 cm by 40.0 cm.
A closely wound rectangular coil of 80 turns has dimensions 25.0 cm by 40.0 cm. The plane of the coil is rotated from a position in which it makes an angle of 37.0 degrees with a magnetic field of 1.10 T to a position perpendicular to the field. The rotation takes 0.0600 s. What is the average emf ε induced in the coil? What is the magnitude of the average emf E induced as the coil is rotated?E= ________ V
The rectangular block below has front-face dimensions of 10 cm by 4 cm, with a depth...
The rectangular block below has front-face dimensions of 10 cm by 4 cm, with a depth of 3 cm.(Figure 1) You will be asked to treat this object as an electrical resistor. Rank the block based on its electrical resistance along the three illustrated coordinate directions (x, y, and z). Rank from largest to smallest. To rank items as equivalent, overlap them. PART B: If all of the dimensions of the block double (to become 20 cm wide, 8 cm...
A closely wound rectangular coil of 80 turns has dimensions 25.0 cm by 40.0 cm. The plane...
A closely wound rectangular coil of 80 turns has dimensions 25.0 cm by 40.0 cm. The plane of the coil is rotated from a position in which it makes an angle of 37.0 degrees with a magnetic field of 1.10 Τ to a position perpendicular to the field. The rotation takes 0.0600 s. What is the average emf ε induced in the coil? What is the magnitude of the average emf E induced as the coil is rotated? E= ________ V
A filtration component consists of a rectangular channel having dimensions H = 10 cm, W =...
A filtration component consists of a rectangular channel having dimensions H = 10 cm, W = 50 cm, and L = 100 cm, containing carbon pellets of diameter 5 mm, is modelled using the Ergun equation. Develop the pressure drop versus mass flowrate (for ?̇ in the range of 1 – 50 kg/s) characteristic for the following porosities (due to packing arrangement): ? = 0.5, 0.7, and 0.9. The fluid properties may be taken to be ρ = 1000 kg/m3...
in a rectangular wave guide for which a = 1.5cm b=0.8cm o=0,m =m0 and E=4e0 Hz=...
in a rectangular wave guide for which a = 1.5cm b=0.8cm o=0,m =m0 and E=4e0 Hz= 2 sin (pi x /a) cos (3piy/b) sin (pi x 10^11 t -bz)a/m. assume TE13 determine of the field components for this mode.
Separate the wave equation in two-dimensional rectangular coordinates x, y. Consider a rectangular membrane, rigidly attache...
Separate the wave equation in two-dimensional rectangular coordinates x, y. Consider a rectangular membrane, rigidly attache to supports along its sides, such that a ≤ x ≤ 0 and b ≤ y ≤ 0. Find the solution, including the specification of the characteristic frequencies of the membrane oscillations. In the case of a = b, show that two or more modes of vibration correspond to a single frequency
In a rectangular waveguide for which a = 1.5 cm, b = 0.8 cm, ? =...
In a rectangular waveguide for which a = 1.5 cm, b = 0.8 cm, ? = 0, ? = ?o and ? = 4?o Hx = 2 sin (?x/a) cos (3?y/b) sin (? x 1011t – ?z) A/m. Assume TE13, determine other field components for this mode.
A solid, rectangular iron bar measures 0.30 cm by 3.0 cm by 25 cm . Part...
A solid, rectangular iron bar measures 0.30 cm by 3.0 cm by 25 cm . Part A Find the resistance between opposing faces with crosssectional area 0.30 cm × 3.0 cm , assuming the faces in question are equipotentials. Express your answer using two significant figures. R = ? Ω Part B Find the resistance between opposing faces with crosssectional area 0.30 cm × 25 cm , assuming the faces in question are equipotentials. R = ? Ω Part C...
A rectangular block of copper has sides of length 12 cm, 26 cm, and 37 cm....
A rectangular block of copper has sides of length 12 cm, 26 cm, and 37 cm. If the block is connected to a 5.4 V source across two of its opposite faces, find the following. (a) What is the maximum current the block can carry? (b) What is the minimum current the block can carry?
A hollow waveguide has dimensions a = 1.5cm and b = 0.8cm. the guide is operating...
A hollow waveguide has dimensions a = 1.5cm and b = 0.8cm. the guide is operating in TE10 mode. The operating frequency (f) is 12GHz. If the component in z for the magnetic field is given by: H_z = 5 * cos? ((?/a) x) *cos? (wt-?z) a) Determine expressions in the time domain of the transverse electric fields (Ex, Ey). substitute any variable in the expression with its values (i.e. ?, ?, k_c, a, b, etc.). b) Determine the maximum...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT