Question

In: Physics

Ques 1: Transient heat (25 pt). A sausage of finite cylindrical shape of a diameter 40...

Ques 1: Transient heat (25 pt).
A sausage of finite cylindrical shape of a diameter 40 mm and a length 100 mm is initially held at a uniform temperature of 20°C. The sausage is then exposed to steam inside a retort at 105 °C. Calculate temperature at the center of the sausage after 15 min of treatment. The convective heat transfer coefficient is 1000 W/(m²K); heat conductivity of the sausage is k= 0.45 W/(m.K), density p=1050 kg/m², specific heat Cp = 3560 J/(kg.K). Assume 2D heat transfer.

Solutions

Expert Solution


Related Solutions

A wood stove is used to heat a single room. The stove is cylindrical in shape,...
A wood stove is used to heat a single room. The stove is cylindrical in shape, with a diameter of 40.0 cm and a length of 50.0cm and operates at a temperature of 400oF. (a) If the temperature of the room is 70.0oF, determine the anount of radiant energy delivered to the room by the stove each second if the emissivity is 0.920. (b) If the room is a square withwalls that are 8.00ft. high and 25.0 ft wide, determine...
Consider cylindrical shape rod of silicon with circular cross-section (resistivity of 3345 , the diameter of...
Consider cylindrical shape rod of silicon with circular cross-section (resistivity of 3345 , the diameter of 2.53 cm and length of 32.7 cm). Consider a voltage of 1.25*103 V is applied. The temperature coefficient of silicon is -0.005 0C-1 (negative because Silicon is a semiconductor). (a) Find the resistance of this rod at room temperature? (2 points) (b) Find the electric field inside the silicon rod? (3 points) (c) Find the energy dissipations in 3 min? (2 points) (d) If...
A cylindrical glass tank with a diameter of 8.6 cm and a height of 25 cm...
A cylindrical glass tank with a diameter of 8.6 cm and a height of 25 cm is inverted and inserted into another tank of water. If no air is allowed to escape from the glass container when submerged, what is the height of the air column in the glass tank when its edge is 2.0 m below the surface of the water?
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100-mm diameter are cooled from an initial temperature of 500ºC by suspending them in an oil bath at 25ºC. If a convection coefficient of 500 W/m2·K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 52ºC, at which point it is withdrawn from the bath? If 9 rods of length 1 m are...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter...
As part of a heat treatment process, cylindrical, 304 stainless steel rods of 100 mm diameter are cooled from an initial temperature of 500°C by suspending them in an oil bath at 30°C. If a convection coefficient of 500 W/m2K is maintained by circulation of the oil, how long does it take for the centerline of a rod to reach a temperature of 50°C, at which point it is withdrawn from the bath? If 10 rods of length L =...
The dimension of the soil sample of a cylindrical shape is provided in Figure 1. In...
The dimension of the soil sample of a cylindrical shape is provided in Figure 1. In its natural moist state, the soil sample has the total weight of 1350 g before the water content determination. The specific gravity, Gs of the soil is given as 2.72. The values obtained for the determination of water content are: The mass of moist soil sample + mass of empty can = 1.415 kg; the mass of fully dry soil sample + mass of...
1. A machine produces metal pieces that are cylindrical in shape. A sample of 36 metal...
1. A machine produces metal pieces that are cylindrical in shape. A sample of 36 metal pieces is taken and the mean diameters for this sample was 6.21 centimeters. In addition from previous studies it is know that the population is approximately Normal with a standard deviation 1.84centimeter. Note: Do the calculations by hand, but show the R code and output for the z-value, t-value or for finding area under the standard normal curve. Note: Round your numbers to exactly...
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm...
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm is subjected to turning using a high speed steel tool. For this tool, n and C values in the Taylor tool life equation are 0.125 and 70 m/min, respectively. The cost for hiring an operator and using the machine tool are $82 per hour. The tooling cost per edge of cutting is $5. Loading and unloading the part on to the machine takes about...
1) pt with a high body temp are often give "alcohol baths". The heat of Vaporization...
1) pt with a high body temp are often give "alcohol baths". The heat of Vaporization of isopropyl alcohol (rubbing alcohol) is 159 cal/g. How much heat is removed from the skin by the evaporation of 190 g (about 1/2 cup) of isopropyl alcohol? 2) Write the equilibrium constant for the reaction of carbon monoxide and oxygen to give carbon (all gases). A) IF (Carbon dioxide)=1.1 M and (oxygen)=.015 M and (carbon monoxide)=.025 M at equilibrium, find K and state...
A sand particle has an average diameter of 1 mm and a shape factor of 0.90...
A sand particle has an average diameter of 1 mm and a shape factor of 0.90 and a specific gravity of 2.1, determine the terminal velocity of the particle settling in water at 20oC (kinematic viscosity of water = 1.003 x 10-6 m2/s and specific gravity = 1) Drag coefficient can be computed using the formula: Cd= 24/Re +( 3/sqrtRe ) + 0.34   Answer: 0.1419 m/s
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT