Question

In: Other

If the gap between C and the rigid wall at D is initially 0.1 mm


If the gap between C and the rigid wall at D is initially 0.1 mm, determine the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of solid A-36 steel cylinders with E = 200 GPa. Also, what is the normal stress developed in the segment AB and the segment BC?

image.png


Solutions

Expert Solution


Related Solutions

A rigid 0.1 m3 container holds 1 kg of water, initially at 25?C. Calculate the theoretical...
A rigid 0.1 m3 container holds 1 kg of water, initially at 25?C. Calculate the theoretical minimum work required to increase the water temperature to the point where the water exists as a single phase. The environment temperature is 25?C.
A rigid tank with a volume of 20 litres initially contains water at 0.1 degree of...
A rigid tank with a volume of 20 litres initially contains water at 0.1 degree of dryness and a pressure of 175 KPA. A steam disposal Valve is located at the top of the tank. Adding heat and steam by throwing the final case degree of dryness 0.4 and pressure 150 kPa is desired to be made. How much mass is ejected and what is the entropy produced. Heat source temperature 1000 K.
A rigid tank of volume 0.75 m3 is initially evacuated. A hole develops in the wall,...
A rigid tank of volume 0.75 m3 is initially evacuated. A hole develops in the wall, and air from the surroundings at 1 bar, 30°C flows in until the pressure in the tank reaches 1 bar. Heat transfer between the contents of the tank and the surroundings is negligible. Determine the final temperature in the tank, in °C.
Two 2.4-mm-diameter beads, C and D, are 11 mm apart, measured between their centers. Bead C...
Two 2.4-mm-diameter beads, C and D, are 11 mm apart, measured between their centers. Bead C has mass 1.0 g and charge 2.5 nC .Bead D has mass 2.0 g and charge -1.0 nC. a) If the beads are released from rest, what is the speed vC of C at the instant the beads collide? b)What is the speed vD of D at the instant the beads collide?
Two 2.1-mm-diameter beads, C and D, are 10 mm apart, measured between their centers. Bead C...
Two 2.1-mm-diameter beads, C and D, are 10 mm apart, measured between their centers. Bead C has mass 1.0 g and charge 1.6 nC. Bead D has mass 2.3 g and charge -1.0 nC. 1) If the beads are released from rest, what is the speed vC of C at the instant the beads collide? 2) What is the speed vD of D at the instant the beads collide?
Two 2.5-mm-diameter beads, C and D, are 11 mm apart, measured between their centers. Bead C...
Two 2.5-mm-diameter beads, C and D, are 11 mm apart, measured between their centers. Bead C has mass 1.0 g and charge 1.8 nC .Bead D has mass 2.5 g and charge -1.0 nC. If the beads are released from rest, what is the speed vC of C at the instant the beads collide? Express your answer to two significant figures and include the appropriate units. What is the speed vD of D at the instant the beads collide? Express...
Two kg of water exist initially as a vapor and liquid at 90°C in a rigid...
Two kg of water exist initially as a vapor and liquid at 90°C in a rigid container of volume 2.42 m3. (a)At what pressure is the system? (b)What is the quality of the system? (c)The temperature of the container is raised to 100°C. What is the quality of the system, and what is the pressure? What are ΔH and ΔU at this point relative to the initial state? (d)As the temperature is increased, at what temperature and pressure does the...
A rigid, sealed container of R134a initially at -30°C and 40% quality is placed inside a...
A rigid, sealed container of R134a initially at -30°C and 40% quality is placed inside a room so that it heats up at 5°C/hr. If there is 3 kg of R134a in the container, determine: a) The volume of the container answer must be 0.2723 m3 b) The specific volume of the vapour when the R134a finishes converting into a gas answer must be 0.09075 m3/kg c) The pressure when all the R134a has finished converting into a gas answer...
A brick wall 25cm thick, initially at 80°C has a medium at 15°C suddenly placed in...
A brick wall 25cm thick, initially at 80°C has a medium at 15°C suddenly placed in conatct with both of its surfaces through a heat transfer coefficient of 90W/m2°C. Find the temperature at a point 2.5cm from the surafce after 10hrs have elapsed. Find also the heat that has flowed out of the wall during that time. Take ρ = 1602kg/m3, cp = 0.84kJ/kg°C, k = 0.69W/m°C,and α = 5.2×10-7m2/s.
One kilogram of Refrigerant 134a vapor initially at 2 bar and 20°C fills a rigid vessel....
One kilogram of Refrigerant 134a vapor initially at 2 bar and 20°C fills a rigid vessel. The vapor is cooled until the temperature becomes -24°C. There is no work during the process. Let To = 20°C, po = 0.1 MPa and ignore the effects of motion and gravity. 2. For the refrigerant, determine the change in exergy, in kJ. Note: for part 1: q=-98.086kj please find part two- the change in exergy in kj
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT