In a two-component phase diagram [temperature (y) vs. composition (x)] the direction of the tie lines...

In a two-component phase diagram [temperature (y) vs. composition (x)] the direction of the tie lines must be determined experimentally.

Group of answer choices

True.

False, they can be inferred from the Lever Rule.

False, they are always horizontal.

Expert Solution

False, they can be inferred from the lever rule.

The position of the point at each end of the tie line, at the boundary of the two-phase area, gives the value of the composition variable of one of the phases and also the
physical state of this phase: either the state of an adjacent one-phase area, or the state of a phase of fixed composition when the boundary is a vertical line. Thus, a
boundary that separates a two-phase area for phases and from a one-phase area for phase is a curve that describes the composition of phase as a function of T or P when it is in equilibrium with phase . The curve is called a solidus, liquidus, or vaporus depending on whether phase ’ is a solid, liquid, or gas.

genius_generous answered 2 years ago

In this phase diagram for water, indicate the direction that the solid-liquid and liquid-gas coexistence lines...

In this phase diagram for water, indicate the direction that the solid-liquid and liquid-gas coexistence lines will move after the addition of solute.

If the x-component of a vector is smaller than its y-component then that vector is in the opposite direction to its y-component.

Which of the following statements is a true statement?If the x-component of a vector is smaller than its y-component then that vector is in the opposite direction to its y-component.A vector's magnitude cannot be more than the magnitude of one of its components.A vector can have positive or negative magnitudes.The magnitude of a vector cannot be zero unless all of its components are zero.A vector's magnitude cannot be less than the sum of the magnitude of its components.

Consider a completely miscible two-component system whose overall composition is X, at a temperature where liquid...

Consider a completely miscible two-component system whose overall composition is X, at a temperature where liquid and gas phases coexist. The composition of the gas phase at this temperature is Xa and the composition of the liquid phase is Xb. Prove the lever rule, which says that the proportion of liquid to gas is (X -Xa)/(Xb -X). Interpret this rule graphically on a phase diagram.

One component phase curve with simple diagram

Demonstrate the construction of phase diagram of one component system with neat sketch.

A two 3- phase transmission lines A & B have the following data: VS = VR...

A two 3- phase transmission lines A & B have the following data: VS = VR = 33 KV/ph , ZA = 2 + j 5 Ω/ph & ZB = 1 + j 6 Ω/ph. Each one delivering 10 MVA at unity p.f. Find: (a)Voltage regulation (b) efficiency and (c) load angle of each T.L.

A student is studying a temperature-composition diagram of a binary mixture of two pure substances, Kimium...

A student is studying a temperature-composition diagram of a binary mixture of two pure substances, Kimium and Kallosium, at 1 atm. The molar mass of Kimium and Kallosium are 80 kg/kmol and 100 kg/kmol respectively. The substances are completely miscible, without any azeotrope at 1 atm. The student has obtained the following data from the diagram. Case Mole % of Kimium Bubble point temperature (degrees C) Dew Point temperature (degrees C) 1 25 100 106 2 45 93 100 a)...

Applying the phase rule. Consider the phase diagram for a one-component system. (a) What is the...

Applying the phase rule. Consider the phase diagram for a one-component system. (a) What is the variance and number of phases at (T1, p1)? (b) What is the variance and number of phases at (T2, p2)? (c) What is the variance and number of phases at (T3, p3)? (d) Which is the triple point?

Water is cooled to 32K, and it appears to be on the solid phase on the phase changing diagram as the temperature is low.

Water is cooled to 32K, and it appears to be on the solid phase on the phase changing diagram as the temperature is low. We compress the ice to a temperature of 340-350K (around 30ATM on the pressure dial).a. Where is the red dot now located in the phase changing diagram? Would it be on the line between liquid and gas phases?b. What does that position on them phase change diagram say about pressure and temperature?c. What happens to the...

What are (a) the x component, (b) the y component, and (c) the z component of...

What are (a) the x component, (b) the y component, and (c) the z component of r Overscript right-arrow EndScripts equals a Overscript right-arrow EndScripts minus b Overscript right-arrow EndScripts plus c Overscript right-arrow EndScripts if a Overscript right-arrow EndScripts equals 5.4 i Overscript ̂ EndScripts plus 1.9 j Overscript ̂ EndScripts minus 3.6 k Overscript ̂ EndScripts , b Overscript right-arrow EndScripts equals negative 4.1 i Overscript ̂ EndScripts plus 5.4 j Overscript ̂ EndScripts plus 3.7 k Overscript...

In the diagram, the dashed lines are parallel to the x axis. The magnitudes of the...

In the diagram, the dashed lines are parallel to the x axis. The magnitudes of the vectors are A = 8.8, B = 6.8, C = 13.5, D = 21.9, and F = 21.9. The angles, in degrees, are θA = 30.0, θB = 53.0, θC = 60.0, θD = 37.0, and θF = 30.0. In this problem, you will be asked to calculate the value of a variety of scalar (dot) products. a) What is A • C? b)...

Question