Oil flowing through a conical tube fixed at an inclined angle of 35° with the horizontal-line...

Oil flowing through a conical tube fixed at an inclined angle of 35° with the horizontal-line and its small diameter downwards. The discharge through the pipe is 0.03m3/s. The diameter of the smaller end is 8cm, while 16cm at another end. The upper end is 2m above lower end. Determine the intensity of pressure at the lower end if the flow takes place in the down direction and the pressure at upwards 1 is 250 kPa. The density of the oil is 0.8505 g/cm3 and the viscosity 79.330 mPa.s.

Expert Solution

genius_generous answered 2 years ago

Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters...

Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters of the elbow at entrance point and exit points are 0.02540 m and 0.01905 m respectively, elbow is 0.1 m high, velocities of water are 5 m/s and 9 m/s at entrance point and exit point respectively, and density of water is 1000 kg/m3, moment flux correction factor = 1.02. Determine gage pressure at inlet Determine vertical component of force of the system, if...

A block is placed on a plane inclined at 35 degrees relative to the horizontal. If...

A block is placed on a plane inclined at 35 degrees relative to the horizontal. If the bloc k slides down the plane with an acceleration of magnitude g/3, determine the coefficient of the kinetic friction between the block and plane.

A 336-kg crate rests on a surface that is inclined above the horizontal at an angle...

A 336-kg crate rests on a surface that is inclined above the horizontal at an angle of 17.2°. A horizontal force (magnitude = 405 N and parallel to the ground, not the incline) is required to start the crate moving down the incline. What is the coefficient of static friction between the crate and the incline?

Driving down a hill inclined at an angle θ with respect to horizontal, you slam on...

Driving down a hill inclined at an angle θ with respect to horizontal, you slam on the brakes to keep from hitting a deer. Your antilock brakes kick in, and you don’t skid. (a) Analyze the forces. (Ignore rolling resistance and air friction.) (b) Find the car’s maximum possible deceleration, a (expressed as a positive number), in terms of g, θ, and the relevant coefficient of friction. √ (c) Explain physically why the car’s mass has no effect on your...

. Oil is flowing in a 150 ft long rock with a cross-sectional area of 35...

. Oil is flowing in a 150 ft long rock with a cross-sectional area of 35 ft2, and permeability of 100 millidarcies at a rate of 6 B/D. The pressures at outlet end is 20 psia. Calculate the pressure at the midpoint of the rock. Oil viscosity is 5 cp

Q.8. Super-heated steam at 875 K is flowing through a thick walled tube of stainless tube...

Q.8. Super-heated steam at 875 K is flowing through a thick walled tube of stainless tube with inside diameter 40mm and outside diameter50mm such that its inner wall is heated to a uniform temperature of 875K.To reduce heat loss, the tube is lagged with 30mm layer of asbestos insulation k=0.2 W/m.K. Calculate the heat loss using the electrical analogy per metre length if the outer surface temperature of the insulated tube is 350K.Thermal conductivity of steel=19 W/m.k.

Water at 35°C is pumped through a horizontal, 200-m-long, 30-mm-diameter tube at 0.25 kg/s. Over time,...

Water at 35°C is pumped through a horizontal, 200-m-long, 30-mm-diameter tube at 0.25 kg/s. Over time, a 2-mm-thick layer of scale of surface roughness e = 200 µ m is deposited on the interior tube wall. Determine the pressure drop from the entrance to the exit of the tube and the required pump power for the clean and fouled conditions.

Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter...

Crude oil of specific gravity (0.75) is flowing through a pipe. The pipe has a diameter of 100 mm and 50 mm at the sections 1 and 2 respectively. The velocity of crude oil at the section 1 is 550 cm/s. The section 1 is 3000 mm and section 2 is 2000 mm above the datum. If the pressure at the section 1 is 0.2 N/mm2, find the intensity of pressure at section 2?

A viscous fluid is flowing through two horizontal pipes. the pressure difference p2 - p1 between...

A viscous fluid is flowing through two horizontal pipes. the pressure difference p2 - p1 between the ends of each pipe is the same. the pipes have the same radius, although one is twice as long as the other. how does the volume flow rate Qb in the longer pipe compare with the rate Qa in the shorter pipe? (A) Qb is the same as Qa (B) Qb is twice as large as Qa (C) Qb is four times as...

A shell-and-tube heat exchanger heats oil from 2°C to 35°C using hot water. The oil flows...

A shell-and-tube heat exchanger heats oil from 2°C to 35°C using hot water. The oil flows in the shell in a single pass. Water flows in 5 copper tubes with a total (all tubes) rate of 0.5 kg/s. Each tube makes 4 passes through the shell and the length per pass is 4 m. The tube inner and outer diameters are 15 mm and 19 mm. The water enters at 95°C and leaves at 29°C. 1. Estimate the average convection...

Question