Question

In: Mechanical Engineering

Issue # 2 - A V-belt from a 10 in. Diameter spindle pulley that rotates at...

Issue # 2 - A V-belt from a 10 in. Diameter spindle pulley that rotates at 1800 rpm, to a 36 in. Diameter flat pulley. The wheelbase is 40 "and the throat angle is 40o. The friction coefficient between the belt and the grooved pulley is 0.2 and with the flat pulley it is also 0.2. The cross section of the straps is a trapezoid with parallel sides of 1.5 "and 0.75", with a height between them of 1 ". The weight of this belt is 0.04 lbf / in3, and the maximum allowable tension on each belt is 200 lbf. Determine: a) How many straps are needed. b) The Torque applied in the transmission, c) The Transmitted power. Note: Consider locating the center of gravity of the belt cross section in order to correct the actual pulley diameter as the band on the splined pulley is slightly outward.)

Solutions

Expert Solution


Related Solutions

In a belt drive the motor pulley has a diameter of 250 mm and rotates at...
In a belt drive the motor pulley has a diameter of 250 mm and rotates at 420 RPM. The machine pulley diameter is 350mm. a) Determine the linear velocity of the belt and the rotational frequency of the machine pulley. b) If the motor pulley accelerates from rest at 2 rads/s^2 how long does it take the motor pulley to reach 420 RPM.
A conveyor belt is driven by a 15" diameter pulley. The conveyor starts from rest and...
A conveyor belt is driven by a 15" diameter pulley. The conveyor starts from rest and accelerates at a constant rate to 100 RPM in 4 seconds, stays at that speed for 3.2 seconds, and then slows to a stop at a constant rate in 3.9 seconds. a) How far will an object on the conveyor travel during this time? b) What is the maximum speed of the belt?
A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a...
A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 2.7 m. The angular speed of the small pulley is 1750 rev/min as it delivers 1.5 kW. The service is such that a service factor Ks of 1.25 is appropriate. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, and Fi. c) Check the...
A vertical wheel with a diameter of 39 cm starts from rest and rotates with a...
A vertical wheel with a diameter of 39 cm starts from rest and rotates with a constant angular acceleration of 7.2 rad/s2 around a fixed axis through its center counterclockwise. a) Through what angle (in degrees) has the point initially at the bottom of the wheel traveled when t = 14 s? (Indicate the direction with the sign of your answer.) b) What is the point's total linear acceleration at this instant? (Enter the magnitude in m/s2.
A 41.0-cm diameter disk rotates with a constant angular acceleration of 2.90 rad/s2. It starts from...
A 41.0-cm diameter disk rotates with a constant angular acceleration of 2.90 rad/s2. It starts from rest at t = 0, and a line drawn from the center of the disk to a point P on the rim of the disk makes an angle of 57.3° with the positive x-axis at this time. (a) At t = 2.49 s, find the angular speed of the wheel. (b) At t = 2.49 s, find the magnitude of the linear velocity AND...
A 45.3-cm diameter disk rotates with a constant angular acceleration of 2.30 rad/s2. It starts from...
A 45.3-cm diameter disk rotates with a constant angular acceleration of 2.30 rad/s2. It starts from rest at t = 0, and a line drawn from the center of the disk to a point P on the rim of the disk makes an angle of 57.3° with the positive x-axis at this time. (a) Find the angular speed of the wheel at t = 2.30 s 5.26 (correct) rad/s (b) Find the linear velocity and tangential acceleration of P at...
A 40.0-cm diameter disk rotates with a constant angular acceleration of 3.00 rad/s2. It starts from...
A 40.0-cm diameter disk rotates with a constant angular acceleration of 3.00 rad/s2. It starts from rest at t = 0, and a line drawn from the center of the disk to a point P on the rim of the disk makes an angle of 57.3° with the positive x-axis at this time. (a) At t = 2.45 s, find the angular speed of the wheel. (b) At t = 2.45 s, find the magnitude of the linear velocity and...
QUESTION 1 A. Gravel is being dumped from a conveyor belt at a rate of 10...
QUESTION 1 A. Gravel is being dumped from a conveyor belt at a rate of 10 cubic feet per minute. It forms a pile in the shape of a right circular cone whose base diameter and height are always the same. How fast is the height of the pile increasing when the pile is 11 feet high? Recall that the volume of a right circular cone with height h and radius of the base r is given by V= 1/3...
Rx: Castor oil 10% (v/v) Tween 80 and Span 20 2% (w/v) Simple syrup qs 50...
Rx: Castor oil 10% (v/v) Tween 80 and Span 20 2% (w/v) Simple syrup qs 50 mL How many gram(s) of Span 20 are needed to prepare for the prescription, given that the required HLB for the emulsion is 10, Span 20 has an HLB of 8.6, and Tween 80 has an HLB of 15?
Brief the following case: Harris v united states 1.Citation. 2 Facts. ... 3 Issue. ... 4...
Brief the following case: Harris v united states 1.Citation. 2 Facts. ... 3 Issue. ... 4 Decision. ... 5 Reason.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT