a- If the radius r of a circle is measured to be r  0.325 +\-...

a-

If the radius r of a circle is measured to be r  0.325 +\- 0.001 m, then calculate the area of the

circle A =  3.14r 2 , as well as the uncertainty in the area.

b-Explain the difference between precision and accuracy.

c-Do systematic errors affect precision or accuracy? Do random errors affect precision or accuracy?

Expert Solution

accuracy describes the difference between the measurement and the part's actual value, while precision describes the variation you see when you measure the same part repeatedly with the same device.

Systematic errors in experimental observations usually come from the measuring instruments. They may occur because:

there is something wrong with the instrument or its data handling system, or
because the instrument is wrongly used by the experimenter.

The accuracy of measurements is often reduced by systematic errors

Random errors in experimental measurements are caused by unknown and unpredictable changes in the experiment. These changes may occur in the measuring instruments or in the environmental conditions.

Examples of causes of random errors are:

electronic noise in the circuit of an electrical instrument,
irregular changes in the heat loss rate from a solar collector due to changes in the wind.

systematic errors affect accuracy while random errors affect precision.

genius_generous answered 2 years ago

1. If the radius r of a circle is measured to be r  0.325 +\-...

1. If the radius r of a circle is measured to be r  0.325 +\- 0.001 m, then calculate the area of the circle A =3.14 r^2, as well as the uncertainty in the area. 2. Explain the difference between precision and accuracy. 3. Do systematic errors affect precision or accuracy? Do random errors affect precision or accuracy?

A circle of radius r has area A = πr2. If a random circle has a...

A circle of radius r has area A = πr2. If a random circle has a radius that is uniformly distributed on the interval (0, 1), what are the mean and variance of the area of the circle? Change the distribution of the radius to an exponential distribution with paramter β = 2. Also find the probability that the area of the circle exceeds 3, if it is known that the area exceeds 2.

1) A circle of radius r has area A = π r2. If a random circle...

1) A circle of radius r has area A = π r2. If a random circle has a radius that is evenly distributed in the interval (0, 1), what are the mean and variance of the area of the circle? choose the correct answer A) 1/3 and 1/12 B) Pi/3 and 1/12 C) Pi/3 and 1/5 D) Pi/3 and (4/45)*Pi^2

15. Let r be a positive real number. The equation for a circle of radius r...

15. Let r be a positive real number. The equation for a circle of radius r whose center is the origin is (x^2)+(y^2)= r^2 . (a) Use implicit differentiation to determine dy/dx . (b) Let (a,b) be a point on the circle with a does not equal 0 and b does not equal 0. Determine the slope of the line tangent to the circle at the point (a,b). (c) Prove that the radius of the circle to the point (a,b)...

Find a path that traces the circle in the plane y=0 with radius r=2 and center...

Find a path that traces the circle in the plane y=0 with radius r=2 and center (2,0,−2) with constant speed 12. r1(s)=〈 , , 〉 Find a vector function that represents the curve of intersection of the paraboloid z=7x^2+5y^2 and the cylinder y=6x^2. Use the variable t for the parameter. r(t)=〈t, , 〉 Need help with Calculus III

In the rolling lab we measured the following conditions: R = 32.25; % roller radius (mm)...

In the rolling lab we measured the following conditions: R = 32.25; % roller radius (mm) Nr = 30; % roll rotational speed in rpm A 8-pass flat rolling process was performed with one set of workpiece dimensional data of length l, width w, and thickness t, measured as below: (with the first set of data for initial solder wire, and the rests are the outlet dimensions of each pass) l = [37.85 39.55 41.39 45.96 50.19 59.83 79.64 127.5...

If the measured power is 18.5 watt, rotational speed is 245 rpm, radius R of inner...

If the measured power is 18.5 watt, rotational speed is 245 rpm, radius R of inner cylinder is 72.5 mm, thickness of liquid is h1 = h2 = 2.35 mm and the height of the fluid is y = 335 mm, determine the viscosity of the viscometer fluid.

How can you generate a circle of center C and radius R using Bresenhem’s algorithm? Also,...

How can you generate a circle of center C and radius R using Bresenhem’s algorithm? Also, make flow chart for this algorithm. Write a C/C++ program to implement Bresenhem’s circle algorithm.

If a circle C with radius 1 rolls along the outside of the circle x2 +...

If a circle C with radius 1 rolls along the outside of the circle x2 + y2 = 36, a fixed point P on C traces out a curve called an epicycloid, with parametric equations x = 7 cos(t) − cos(7t), y = 7 sin(t) − sin(7t). Graph the epicycloid. Find the area it encloses.

(C++ programming) Assignment *Circle Class -Radius r (private) as an attribute variable -Member function -Get(): Function...

(C++ programming) Assignment *Circle Class -Radius r (private) as an attribute variable -Member function -Get(): Function that returns r value of property variable -Put(int d): A function that stores d in attribute variable r *Declare a one-dimensional array of type Circle and in each array element Read and store integers from standard input device *Declare the swap() function to swap two elements with each other *Write a program that sorts the elements of a one-dimensional array of circle type in...

Question