Air flows through a heating duct with a square cross-section with 5-inch sides at a speed...

Air flows through a heating duct with a square cross-section with 5-inch sides at a speed of 5.3 ft/s. Just before reaching an outlet in the floor of a room, the duct widens to assume a square cross-section with sides equal to 13 inches. Compute the speed of the air flowing into the room (in ft/s), assuming that we can treat the air as an incompressible fluid. Answer should be in Ft/s

Expert Solution

genius_generous answered 2 years ago

Hot air flows with a mass flow rate of 0.05 kg/s through an insulated square duct...

Hot air flows with a mass flow rate of 0.05 kg/s through an insulated square duct with side of 0.15m, the hot air enters at 103 oC and after a distance of 5m, cools to 85 oC. The heat transfer coefficient between the duct outer surface and the ambient air (Tair = 0 oC) is 6 W/m2 K. Calculate the heat transfer coefficient between hot air and duct inner wall. Air Cp = 1.011 KJ/kg K; air k = 0.0306...

Air flows through a constant area duct. The pressure and temperature of the air at the...

Air flows through a constant area duct. The pressure and temperature of the air at the inlet to the duct are P1 = 100 kPa absolute, and T1 = 298 K, respectively. Inlet Mach number is M1 = 0.1. Heat is transferred to the air as it flows through the duct and as a result the Mach number at the exit increases. Write a Matlab code and plot the following: a) Find the pressure and temperature at the exit, while...

Airflow through a long, 0.15-m-square air conditioning duct maintains the outer duct surface temperature at 10°C....

Airflow through a long, 0.15-m-square air conditioning duct maintains the outer duct surface temperature at 10°C. If the horizontal duct is uninsulated and exposed to air at 35°C in the crawlspace beneath a home, what is the heat gain per unit length of the duct? Evaluate the properties of air at 300 K. For the sides of the duct, use the more accurate Churchill and Chu correlations for laminar flow on vertical plates. What is the Rayleigh number for free...

Air is cooled from 300 K to 273 K as it flows steadily through a duct....

Air is cooled from 300 K to 273 K as it flows steadily through a duct. Frictional dissipation may be neglected. Cooling is achieved by removing heat via a heat pump. The work requirement is 1.15 times that of a reversible heat pump operating between 263 and 310 K. For each mole of air flowing through the duct, calculate: Air can be assumed an ideal gas with a constant heat capacity cP of 3.50R. The temperature of the surroundings is...

An 8-m-long, uninsulated square duct of cross section 0.2 m X 0.2 m and relative roughness...

An 8-m-long, uninsulated square duct of cross section 0.2 m X 0.2 m and relative roughness 10-3 passes through the attic space of a house. Hot air enters the duct at 1 atm and 91oC at a volume flow rate of 0.15 m3/s. The duct surface is nearly isothermal at 60oC. Determine the rate of heat loss from the duct to the attic space and the pressure difference between the inlet and outlet sections of the duct. Evaluate air properties...

Air flows through a short duct with a smooth inside surface and gradually changing flow area....

Air flows through a short duct with a smooth inside surface and gradually changing flow area. The measured flow rate is equal to 288 lbm/min. At the duct inlet, the temperature is equal to 82 deg F, and the pressure is equal to 15 psia. The inlet velocity is equal to 924 ft/s. At the duct exit, the pressure is equal to 21.7 psia. (I.) Calculate the cross-sectional flow area of the duct inlet. (II.) Estimate the temperature and velocity...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the stagnation temperature is 90°C. If the Mach number at the exit is 0.3, determine the direction and the rate of heat transfer. For the same conditions at the inlet, determine the amount of heat that must be transferred to the system if the flow is to be sonic at the exit of the duct.

A liquid (ρ = 1.65 g/cm3) flows through a horizontal pipe of varying cross section as...

A liquid (ρ = 1.65 g/cm3) flows through a horizontal pipe of varying cross section as in the figure below. In the first section, the cross-sectional area is 10.0 cm2, the flow speed is 281 cm/s, and the pressure is 1.20 105 Pa. In the second section, the cross-sectional area is 4.50 cm2. The flow within a horizontal tube is depicted by five lines. The tube extends from left to right, with the left end wider than the right end. The...

A long conducting pipe has a rectangular cross section with sides of lengths a and b....

A long conducting pipe has a rectangular cross section with sides of lengths a and b. One face of the pipe is maintained at a constant potential V = V0 while the other 3 faces are grounded (V = 0). Using separation of variables, find the potential for points inside the pipe V (x,y).

Air flows through a 8-in-diameter, 60-ft-long adiabatic duct with inlet conditions of V1= 550 ft/s, T01=...

Air flows through a 8-in-diameter, 60-ft-long adiabatic duct with inlet conditions of V1= 550 ft/s, T01= 650 R, and P1= 50 psia. For an average friction factor of 0.03, determine the velocity, temperature, and pressure at the exit of the duct. Please DO NOT merely copy other expert's work. I would like original work.

Question