Q2. Design a rectangular column: PD = 400 k, PL= 600 k, ρ = 2 %....

Q2. Design a rectangular column: PD = 400 k, PL= 600 k, ρ = 2 %. fc’ = 4000 psi, fy = 60,000 psi. Draw the reinforcement detail also.

Please ANSWER this question with clear and with all steps don't miss any calculation and drawing steps.

- Don't consider the foundation. Assume any dimension of the column that can carry this loads. the important that the column not fail by using ACI code.

Solutions

Expert Solution

Complete solution is given below.

Ally Wells answered 1 month ago

Next > < Previous

Related Solutions

Design for flexure a simple span beam 26’ long to carry PD = 1000# and PL...

Design for flexure a simple span beam 26’ long to carry PD = 1000# and PL = 2000# at the center of the span. f’c = 4,000psi and fy = 60,000psi. show all work

Design a square concrete column footing to support a 400-mm x 400-mm reinforced concrete column. The...

Design a square concrete column footing to support a 400-mm x 400-mm reinforced concrete column. The center of the column and footing must coincide. Loads: ???=350 ??, ???=480 ??, ???=100 ??−?, ???=130 ??−? Column Design Criteria: ??′=28 ???, ??=400??? Footing Design Criteria: ??′=28 ???, ??=400???, ??=180 ???,??=1.70 ?, ??=16 ??/?3,??=24 ??/?3, ??=25 ??, assume a thickness of the footing of 700 mm.

Design a rectangular footing for an 18-in square interior column with a dead load of 210...

Design a rectangular footing for an 18-in square interior column with a dead load of 210 k and a live load of 180 k. Make the length of the long side equal to twice the width of the short side, fy = 60,000 psi, fc' = 4000 psi, normal weight, and qallowable= 3650 psf. Assume the base of the footing is 5 ft 0 in below-grade , γ concrete = 150 pcf and γ soil = 100 pcf. Also, assume...

Design a rectangular reinforced concrete beam to resist a total design moment Mu=400 ft.kips (this includes...

Design a rectangular reinforced concrete beam to resist a total design moment Mu=400 ft.kips (this includes the moment due to beam weight). Architectural considerations require that the width (b) be 18 in. and the overall depth (h) be 26 in. Use f′c=4,000 psi and fy=60,000 psi. Sketch your design.

Design an isolated rectangular footing to support an interior column 40 cm × 40 cm in...

Design an isolated rectangular footing to support an interior column 40 cm × 40 cm in cross section and carries a dead load of 800 kN and a live load of 600 kN. Use f́c= 21 MPa, fy= 420 MPa, q all (net) =200 kN / m2 , γsoil = 17 kN /m3 , and Df =1.25 m. Space limitations are such that one lateral dimension cannot exceed 2.5 m

Determine the mean energy at 400 K of a two-level system. The energy separation is 600...

Determine the mean energy at 400 K of a two-level system. The energy separation is 600 /cm.

A 600 ft.^2 rectangular patch is to be enclosed by a fence and divided into two...

A 600 ft.^2 rectangular patch is to be enclosed by a fence and divided into two equal parts by another fence parallel to one of the sides. what dimensions for the outer rectangle would will require the smallest total length of fence?

Design a square tied column to support an axial dead load of (W1) k and an...

Design a square tied column to support an axial dead load of (W1) k and an axial live load of (W2) k. Begin using approximately (X) percent longitudinal steel, a concrete strength of 4,000 psi and Grade 60 steel. Draw the details of reinforcement and check all ACI recommendation. W1 = 220 k W2 = 165 k X = 2%

Design a reinforced concrete steel rectangular tie column with ACI standards, total LL = 14.0625 kips,...

Design a reinforced concrete steel rectangular tie column with ACI standards, total LL = 14.0625 kips, total DL = 18.95625kips, cross-section 12in by 12 in, Hight of column 12ft. Show all the steps and which table used. Assume the information which is not given with justifications. Show drawing as well. If the high is not suitable you can change it.

Design an isolated footing with one side limited to 7 ft for the following: 1 ft x 1 ft edge column, axial loads PD = 130 kip and PL = 155 kip, fc’ = 3,000 psi, fy = 60,000 psi, qa = 4 ksf

Design an isolated footing with one side limited to 7 ft for the following: 1 ft x 1 ft edge column, axial loads PD = 130 kip and PL = 155 kip, fc’ = 3,000 psi, fy = 60,000 psi, qa = 4 ksf, and a distance from top of backfill to bottom of footing is 4 ft. Assume the soil density is 100 pcf. For the column, fc’ = 5,000 psi. Sketch your design.

Subjects