Design a rectangular footing for an 18-in square interior column with a dead load of 210...

Design a rectangular footing for an 18-in square interior column with a dead load of 210 k and a live load of 180 k. Make the length of the long side equal to twice the width of the short side, fy = 60,000 psi, fc' = 4000 psi, normal weight, and qallowable= 3650 psf. Assume the base of the footing is 5 ft 0 in below-grade , γ concrete = 150 pcf and γ soil = 100 pcf. Also, assume h=24 in and cover = 4.5 in .

Answer the following questions :

a- Find the required area then the dimensions of the footing .

b- Check one way shear.

c- Check the punching shear.

d- Design the reinforcement in both directions .

Expert Solution

Ally Wells answered 9 months ago

. Design a square footing for a 16-in. square interior column with an ultimate dead load...

. Design a square footing for a 16-in. square interior column with an ultimate dead load = 300 (k) and an ultimate live load = 200 (k). Take fy=60,000 psi, fc=4000 psi, normal weight, and qa= 4500 psf. Assume the base of the footing is 4 (ft.) below grade. Draw the reinforcement detail also. Check for one way and two way shears with the support of diagram. With ACI code

Q.2. Design a square footing for a 16-in. square interior column with an ultimate dead load...

Q.2. Design a square footing for a 16-in. square interior column with an ultimate dead load = W1 (k) and an ultimate live load = W2 (k). Take fy=60,000 psi, fc=4000 psi, normal weight, and qa= (w) psf. Assume the base of the footing is h (ft.) below grade. Draw the reinforcement detail also. Check for one way and two way shears with the support of diagram. Student shall take the data given below in the table against...

Design a square footing for a 18-inch. square column and a superimposed dead load of 200...

Design a square footing for a 18-inch. square column and a superimposed dead load of 200 kips and a live load of 300 kips. The maximum permissible soil pressure is 4000 psf. Use concrete with a design strength of 3 ksi and grade 40 reinforcing bars with yield strength of 40 ksi.

Design a square interior column footing for a 15-in. square tied interior column that supports a...

Design a square interior column footing for a 15-in. square tied interior column that supports a dead load of 160 kips and live load of 180 kips. The column is reinforced with eight # 8 bars, also, the base of the footing is 6 ft below the grade line, the soil weight is 100 lb/ft3, the concrete weight is 150 lb/ft3, f’c = 4,000 psi, fy = 60,000 psi and qa = 4 kip/ft2.

QUESTIONS: Design a square column footing for a 20-in. square tied interior column that supports loads...

QUESTIONS: Design a square column footing for a 20-in. square tied interior column that supports loads of DL (170) k and Live load LL (210) k. The column is reinforced with eight No 8 bars, the bottom of the footing is 5 foot below final grade, and the soil weighs 100 lb. /ft3 the allowable soil pressure is 4 w ksf. The concrete strength is 4,000 psi and the steel is Grade 60.

Design an isolated rectangular footing to support an interior column 40 cm × 40 cm in...

Design an isolated rectangular footing to support an interior column 40 cm × 40 cm in cross section and carries a dead load of 800 kN and a live load of 600 kN. Use f́c= 21 MPa, fy= 420 MPa, q all (net) =200 kN / m2 , γsoil = 17 kN /m3 , and Df =1.25 m. Space limitations are such that one lateral dimension cannot exceed 2.5 m

Design a square tied column to support an axial dead load of (W1) k and an...

Design a square tied column to support an axial dead load of (W1) k and an axial live load of (W2) k. Begin using approximately (X) percent longitudinal steel, a concrete strength of 4,000 psi and Grade 60 steel. Draw the details of reinforcement and check all ACI recommendation. W1 = 220 k W2 = 165 k X = 2%

Using the formulas and codes provided by ACI 318 1. Design a square interior column footing...

Using the formulas and codes provided by ACI 318 1. Design a square interior column footing for a 15-in. square tied interior column that supports a dead load of 160 kips and live load of 180 kips. The column is reinforced with eight # 8 bars, also, the base of the footing is 6 ft below the grade line, the soil weight is 100 lb/ft3, the concrete weight is 150 lb/ft3, f’c = 4,000 psi, fy = 60,000 psi and...

A square footing is supporting a single interior column with a dimension of 12 in ×...

A square footing is supporting a single interior column with a dimension of 12 in × 12 in. The column carries axial loads as follows: 100 kip dead load and 80 kip live load. Use normal-weight concrete with ?? ′ = 3 ksi, ?? = 60 ksi, and ?? = 5 ksf. The distance from the bottom of the footing to final grade is 5 ft. The height of the footing is 36 in and the concrete cover is 3.5...

What will be the width (B in meter) of a square footing to support rectangular column...

What will be the width (B in meter) of a square footing to support rectangular column 40x40 cm and carries a dead load of 614 kN and live load of 477 kN. The net allowable bearing pressure is 180 kPa. The design should be according to (ACI) code with the following parameters: fc’ = 28 MPa, fy = 420 MPa.

Question