Question

In: Physics

Water flows at a rate of 28 L/min through a horizontal 7.5-cm-diameter pipe under a pressure...

Water flows at a rate of 28 L/min through a horizontal 7.5-cm-diameter pipe under a pressure of 8.1 Pa. At one point, calcium deposits reduce the cross-sectional area of the pipe to 33 cm^2. What is the pressure at this point? (consider the water to be an ideal fluid.)

Solutions

Expert Solution


Related Solutions

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...
A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?
A 7.7 cm diameter horizontal pipe gradually narrows to 6.0 cm . When water flows through...
A 7.7 cm diameter horizontal pipe gradually narrows to 6.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 34.0 kPa and 22.8 kPa , respectively. What is the volume rate of flow?
A 5.1 cm diameter horizontal pipe gradually narrows to 2.5 cm . When water flows through...
A 5.1 cm diameter horizontal pipe gradually narrows to 2.5 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 35.0 kPa and 21.8 kPa , respectively. What is the volume rate of flow?
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...
Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water? You may ignore any minor loses.
a- Water enters a house through a pipe with inside diameter of 3.0 cm at an...
a- Water enters a house through a pipe with inside diameter of 3.0 cm at an absolute pressure of 5.0 X 105 Pa. A 1.5 cm diameter pipe leads to the second-floor bathroom 6.0 m above. When the flow speed at the inlet pipe is 2.0 m/s find: - Flow speed (velocity) of the water in the bathroom - Pressure water in the bathroom? - Calculate the volume flow rate in the bathroom.
A 1.0-cm-diameter pipe widens to 2.0 cm, then narrows to 0.5 cm. Liquid flows through the...
A 1.0-cm-diameter pipe widens to 2.0 cm, then narrows to 0.5 cm. Liquid flows through the first segment at a speed of 9.0 m/s . What is the speed in the second segment? What is the speed in the third segment? What is the volume flow rate through the pipe? for the love of god please give me the right answer. everyone has given me the wrong answers so far and i'm pissed off.
A 1.0-cm-diameter pipe widens to 2.0 cm, then narrows to 0.5 cm. Liquid flows through the...
A 1.0-cm-diameter pipe widens to 2.0 cm, then narrows to 0.5 cm. Liquid flows through the first segment at a speed of 9.0 m/s . What is the speed in the second segment? What is the speed in the third segment? What is the volume flow rate through the pipe?
Water flows upward and then is discharged to the right through a 3 inch diameter pipe...
Water flows upward and then is discharged to the right through a 3 inch diameter pipe elbow, at a steady flow rate of 1 cubic foot per second, the gage pressure at the entrance to the elbow is 30 psi. What vertical and horizontal force is necessary to hold the elbow stationary, neglecting any required torque.
Water is being pumped through a horizontal pipe that is 36.0 m long and 13.5 cm...
Water is being pumped through a horizontal pipe that is 36.0 m long and 13.5 cm in diameter. A pump maintains a gauge pressure of 742 Pa at a large open tank at one end of the pipe. The other end of the pipe is open to the air. If this pipe is replaced by a second one of length 9 m and diameter 5.0 cm, what gauge pressure must the pump provide to give the same volume flow rate...
A horizontal pipe 10 cm in diameter and 3000 cm long is filled with a sand...
A horizontal pipe 10 cm in diameter and 3000 cm long is filled with a sand of 20 % porosity. The permeability of the sand is estimated to be 250 md. The sand is saturated with an oil of viscosity 0.65 cp, and the same oil is injected into the sand pipe. You are asked to calculate a. What is the Darcy velocity in the sand pipe under a 100-psi pressure differential? b. What is the flow rate through the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT