Question

In: Other

A double-pipe heat exchanger operating in counter current mode is to heat a fluid(Cp 1.7 kJ/kg...

A double-pipe heat exchanger operating in counter current mode is to heat a
fluid(Cp 1.7 kJ/kg K) from 50°C to 95°C at a rate of 4.5 kg/s. The heating is to be
accomplished by hot fluid (Cp=1.97 kJ/kg K) available at 200°C at a mass flow
rate of 6 kg/s. The inner tube is thin-walled and has a diameter of 4 cm. If the
overall heat transfer coefficient of the heat exchanger is 680 W/m2
°C,
determine the length of the heat exchanger required to achieve the desired
heating.

Data given:

Plastic 0.4 W/mK
brick 0.72W/m°C
plaster 0.36 W/m°C
cement 1.4 W/m°C
Polyurethane foam 0.025W/m °C
Glass fiber/fiber glass 0.036 W/m °C
Air 0.0198 W/m °C
Copper 380W/m °C

# just take the required data that u need

Solutions

Expert Solution


Related Solutions

A counter-flow double-pipe heat exchanger is to heat water from 20ºC to 80ºC at a rate...
A counter-flow double-pipe heat exchanger is to heat water from 20ºC to 80ºC at a rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160ºC at a mass flow rate of 2 kg/s. The inner tube is thin-walled, and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640 W/(m2.ºC), determine the length of the heat exchanger required to achieve the desired heating using the effectiveness-NTU...
A counter-flow double-pipe heat exchanger is heating water from 20 to 80 C at a rate...
A counter-flow double-pipe heat exchanger is heating water from 20 to 80 C at a rate of 1.2 kg/s. The heating is provided by water at 160 C and a rate of 2 kg/s. The inner tube has a diameter of 1.5 cm, and the U is 640 W/m2 K. Use the effectiveness-NTU method to determine the length of the heat exchanger required.
Water flowing at a rate of 0.667 kg/s (Cp = 4.192 kJ/kg. K) enters a counter...
Water flowing at a rate of 0.667 kg/s (Cp = 4.192 kJ/kg. K) enters a counter current heat exchanger at 318 K and is heated by an oil stream entering at 393 K at a rate of 2.85 kg/s (Cp=1.89 kJ/kg. K). The overall U=290 W/m2. K and the area A=20 m2. Calculate the heat transfer rate and the exit water temperature.
A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil...
A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil from 250°F to 120°F using 10 gal/min of cooling water available at 70°F. The heat exchanger is to consist of sections of 0.75 inch 16 BWG copper tubing inside 1.5 inch 16 BWG tubing; the water flows in the annular space. The shell-side heat transfer coefficient for this system is known to be 737 Btu/hr×ft2×°F. a) Estimate the required length of the countercurrent exchanger,...
A double-pipe heat exchanger is designed as an engine oil cooler. The flow rate of oil...
A double-pipe heat exchanger is designed as an engine oil cooler. The flow rate of oil is 5 kg/s, and it will be cooled from 60°C to 40°C through annulus (ID = 0.10226 m, OD = 0.1143 m). Sea water flows through the tubes (ID = 0.02664 m, OD = 0.03340 m) and is heated from 10°C to 30°C. The number of bare tubes in the annulus is 3, and the length of the hairpin is 3 m. Assume that...
For the double-pipe heat exchanger of Problem 3.10, calculate the outlet temperatures of the two streams...
For the double-pipe heat exchanger of Problem 3.10, calculate the outlet temperatures of the two streams when the unit is first placed in service. Q:3.10 A hydrocarbon stream is to be cooled from 200◦F to 130◦F using 10,800 lb/h of water with a range of 75–125◦F. A double-pipe heat exchanger comprised of 25 ft long carbon steel hairpins will be used. The inner and outer pipes are 1.5- and 3.5-in. schedule 40, respectively. The hydrocarbon will flow through the inner...
A 10 ft long double pipe heat exchanger consisting of a 1 in sch 40 (1.315...
A 10 ft long double pipe heat exchanger consisting of a 1 in sch 40 (1.315 in OD, 1.029 in ID) inner pipe within a 4 in sch 40 (3.998 in ID) outer pipe uses chilled water to cool hot glycerin (the water flows in the annulus and glycerin in the inner pipe). The pipes are constructed of AISI 302 stainless steel. The mean velocities of the water and glycerin are 4 ft/s and 1.3 ft/s, respectively. If the average...
A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an...
A double-pipe heat exchanger is used to condense steam at 40°C saturation temperature. Water at an average bulk temperature of 20°C flows at 2 m/s through the inner tube (copper, 2.54 cm ID, 3.05 cm OD). Steam at its saturation temperature flows in the annulus formed between the outer surface of the inner tube and outer tube of 6 cm ID. The average heat transfer coefficient of the condensing steam is 6,000 W/m2 ? K, and the thermal resistance of...
Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of...
Water is used to cool ethylene glycol in a 18.3-m-long double pipe heat exchanger made of 4-std and 2-std (both type M) copper tubing. The water inlet temperature is 15.6°C and the ethylene glycol inlet temperature is 82.2°C. The flow rate of the ethylene glycol is 9.07 kg/s, while that for the water is 13.6 kg/s. Calculate the expected outlet temperature of the ethylene glycol and determine the pressure drop expected for both streams. Assume counterflow, and place the ethylene...
Tomato soup is flowing through a double-pipe heat exchanger (3 cm ID, 4.2 cm OD), with...
Tomato soup is flowing through a double-pipe heat exchanger (3 cm ID, 4.2 cm OD), with saturated steam at 112°C on the outside of the pipe. The convective heat transfer coefficient between the soup to the pipe is 323 W/m2 K and the convective heat transfer coefficient between the steam to the pipe is very large. The thermal conductivity of the soup and pipe are 0.89 W/m K and 15.6 W/m K, respectively. 1. For this system: A. The overall...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT