Question

Discuss nuclear gas cycle in detail. Please make a diagram of nuclear gas cycle integrated with Multi-effect distillation with detailed explanation.

Answer 1

Gas cycle integrated with multi effect distillation not is found.

Remaining answer is shown below.

The nuclear fuel cycle consists of front-end steps that prepare uranium for use in nuclear reactors and back-end steps to safely manage, prepare, and dispose of used—or spent—but still highly radioactive spent nuclear fuel.

Uranium is the most widely used fuel by nuclear power plants for nuclear fission. Nuclear power plants use a certain type of uranium—U-235—as fuel because its atoms are easily split apart. Although uranium is about 100 times more common than silver, U-235 is relatively rare at just over 0.7% of natural uranium. Uranium concentrate is separated from uranium ore at uranium mills or from a slurry at in-situ leaching facilities. It is then processed in conversion and enrichment facilities, which increases the level of U-235 to between 3%–5% for commercial nuclear reactors, and made into reactor fuel pellets and fuel rods in reactor fuel fabrication plants.

Nuclear fuel is loaded into reactors and used until the fuel assemblies become highly radioactive and must be removed for temporary storage and eventual disposal.

  

The front end of the nuclear fuel cycyclecle

Exploration

The nuclear fuel cycle starts with exploration for uranium and the development of mines to extract uranium ore. A variety of techniques are used to locate uranium, such as airborne radiometric surveys, chemical sampling of groundwater and soils, and exploratory drilling to understand the underlying geology. Once uranium ore deposits are located, the mine developer usually follows up with more closely spaced in fill, or development drilling, to determine how much uranium is available and what it might cost to recover it.

Uranium mining

When ore deposits that are economically feasible to recover are located, the next step in the fuel cycle is to mine the ore using one of the following techniques:

• underground mining
• open pit mining
• in-place (in-situ) solution mining
• heap leaching

Before 1980, most U.S. uranium was produced using open pit and underground mining techniques. Today, most U.S. uranium is produced using a solution mining technique commonly called in-situ-leach (ISL) or in-situ-recovery (ISR). This process extracts uranium that coats the sand and gravel particles of groundwater reservoirs. The sand and gravel particles are exposed to a solution with a pH that has been elevated slightly by using oxygen, carbon dioxide, or caustic soda. The uranium dissolves into the groundwater, which is pumped out of the reservoir and processed at a uranium mill. Heap leaching involves spraying an acidic liquid solution onto piles of crushed uranium ore. The solution drains down through the crushed ore and leaches uranium out of the rock, which is recovered from underneath the pile. Heap leaching is no longer used in the United States.

Uranium conversion

The next step in the nuclear fuel cycle is to convert yellowcake into uranium hexafluoride (UF6) gas at a converter facility. Three forms (isotopes) of uranium occur in nature: U-234, U-235, and U-238. Current U.S. nuclear reactor designs require a stronger concentration (enrichment) of the U-235 isotope to operate efficiently. The uranium hexafluoride gas produced in the converter facility is called natural UF6 because the original concentrations of uranium isotopes are unchanged.

Uranium enrichment

After conversion, the UF6 gas is sent to an enrichment plant where the individual uranium isotopes are separated to produce enriched UF6, which has a 3% to 5% concentration of U-235.

Two types of uranium enrichment processes have been used in the United States: gaseous diffusion and gas centrifuge. The United States currently has one operating enrichment plant, which uses a gas centrifuge process. Enriched UF6 is sealed in canisters and allowed to cool and solidify before it is transported to a nuclear reactor fuel assembly plant by train, truck, or barge.

Atomic vapor laser isotope separation (AVLIS) and molecular laser isotope separation (MLIS) are new enrichment technologies currently under development. These laser-based enrichment processes can achieve higher initial enrichment (isotope separation) factors than the diffusion or centrifuge processes and can produce enriched uranium more quickly than other techniques.

Uranium reconversion and nuclear fuel fabrication

Once the uranium is enriched, it is ready to be converted into nuclear fuel. At a nuclear fuel fabrication facility, the UF6, in solid form, is heated to gaseous form, and then the UF6 gas is chemically processed to form uranium dioxide (UO2) powder. The powder is then compressed and formed into small ceramic fuel pellets. The pellets are stacked and sealed into long metal tubes that are about 1 centimeter in diameter to form fuel rods. The fuel rods are then bundled together to make up a fuel assembly. Depending on the reactor type, each fuel assembly has about 179 to 264 fuel rods. A typical reactor core holds 121 to 193 fuel assemblies.

At the reactor

Once the fuel assemblies are fabricated, trucks transport them to the reactor sites. The fuel assemblies are stored onsite in fresh fuel storage bins until the reactor operators need them. At this stage, the uranium is only mildly radioactive, and essentially all radiation is contained within the metal tubes. Typically, reactor operators change out about one-third of the reactor core (40 to 90 fuel assemblies) every 12 to 24 months.

The reactor core is a cylindrical arrangement of the fuel bundles that is about 12 feet in diameter and 14 feet tall and encased in a steel pressure vessel with walls that are several inches thick. The reactor core has essentially no moving parts except for a small number of control rods that are inserted to regulate the nuclear fission reaction. Placing the fuel assemblies next to each other and adding water initiates the nuclear reaction.

A nuclear fuel assembly

The back end of the nuclear fuel cycle

Interim storage and final disposal in the United States

After use in the reactor, fuel assemblies become highly radioactive and must be removed and stored under water at the reactor site in a spent fuel pool for several years. Even though the fission reaction has stopped, the spent fuel continues to give off heat from the decay of the radioactive elements that were created when the uranium atoms were split apart. The water in the pool serves to both cool the fuel and block the release of radiation.

Within a few years, the spent fuel cools in the pool and may be moved to a dry cask storage container at the power plant site. An increasing number of reactor operators now store their older spent fuel in these special outdoor concrete or steel containers with air cooling. Learn more about spent fuel storage.

The final step in the nuclear fuel cycle is the collection of spent fuel assemblies from the interim storage sites for final disposition in a permanent underground repository. The United States currently has no permanent underground repository for high-level nuclear waste.