One mole of carbon monoxide at 10 ºC is completely burnt at 1 atm pressure with...

One mole of carbon monoxide at 10 ºC is completely burnt at 1 atm pressure with 50% excess air. The air is fed to the burner at a temperature of 540 ºC. The combustion products leave the burner chamber at 425 ºC. Use a molar flow and enthalpy summary table to help organize your work.

Draw a labeled PFD. Define your system. Analyze the energy balance relationship that applies to your system.
Calculate the heat involved in this process, in units of kJ per mole of CO combusted.

Solutions

Expert Solution

Amanda K answered 1 month ago

Next > < Previous

Related Solutions

One mole of carbon dioxide gas occupies a volume of 24.346 L at 25 ºC. It...

One mole of carbon dioxide gas occupies a volume of 24.346 L at 25 ºC. It is slowly compressed isothermally to a volume of 12.173 L. Assume that CO2 behaves as a van der Waals gas. It is known that, for a van der Waals gas, , dU = a n2 V-2 dV. Find a. w, the work done in Joules on the gas during the compression (10 pts) b. q, the heat flow in Joules into the gas during...

A mixture 0.500 mole of carbon monoxide and 0.400 mole of bromine was placed into a...

A mixture 0.500 mole of carbon monoxide and 0.400 mole of bromine was placed into a rigid 1.00 L container and the system was allowed to come to equilibrium. The equilibrium concentration of COBr2 was 0.233 M. What is the value of Kc for this reaction? CO(g) + Br2(g) ------>(equilb. arrows) COBr2(g)

1.Humid air at 50 ºC and 1.0 atm with 2 ºC of superheat is fed to...

1.Humid air at 50 ºC and 1.0 atm with 2 ºC of superheat is fed to the condenser. Gas and liquid streams leave the condenser in equilibrium at 20 ºC and 1 atm. (a)Assume a basis of calculation of 100 mol inlet air, draw and label a flow chart for the process. (b)Calculate the mass of water condensed per m3 of air fed and kJ transferred per m3 air fed. (c)What cooling rate (kW) would be required to process 250...

A hydrogen-rich gas stream contains 1.0 mole % carbon monoxide. It is desired to use a...

A hydrogen-rich gas stream contains 1.0 mole % carbon monoxide. It is desired to use a microporous ceramic membrane for separating carbon monoxide (CO) from hydrogen gas at a pressure of 1 atm and a temperature of 400C. The average pore diameter of the membrane is 15 nm and the void fraction is 0.30. a) Estimate the molecular diffusivity of CO in a mixture with H2 b) Determine the Knudsen diffusion coefficient and the effective diffusion coefficient for CO in...

At 1.00 atm pressure and 273 K one mole of gas should occupy 22.4 L. What...

At 1.00 atm pressure and 273 K one mole of gas should occupy 22.4 L. What volume would one mole of gas occupy at 21 oC and 1.00 atm? In the Molar Mass of Magnesium experiment: a) At the end of the reaction, the temperature was 21.5 oC (294.65 K), 99.2 mL of gas were formed, and the pressure was 1.00 atm in the gas syringe. The Gas Constant has a value of 0.08206 L atm/ (mol K) (Pay attention...

1 - The LC50 for carbon monoxide alone is 6600 ppm. For a mixture of carbon...

1 - The LC50 for carbon monoxide alone is 6600 ppm. For a mixture of carbon monoxide and 5% carbon dioxide, the LC50 for CO drops to 3900 ppm. 5% carbon dioxide by itself is not lethal. Which of the following statements is appropriate based on this data? a)CO2potentiates the effect of CO b)CO2is an antagonist for CO c)CO2exerts a synergistic effect in combination with CO 2 - The specific endocytosis process by which liquids or very small particles are...

one mole of ice at 0 C is turned completely into steam by heating under 1...

one mole of ice at 0 C is turned completely into steam by heating under 1 atm pressure. calculate the entropy change in the system with specific heat capacity and enthalpy/heat values.assuming they are all constant.

2.50 mole of perfect gas at 0°C is expanded from an initial pressure of 5.00 atm...

2.50 mole of perfect gas at 0°C is expanded from an initial pressure of 5.00 atm to a final pressure of 1.00 atm against a constant external pressure of 1.00 atm. (a) isothermally and (b) adiabatically. (1) Calculate the values of q, w, DU, DH, DS, DSsur and DStot for (a) and (b) (2) Draw p -V diagram to represent these two different paths.

One kg mole of an ideal gas is compressed isothermally at 127°C from 1 atm to...

One kg mole of an ideal gas is compressed isothermally at 127°C from 1 atm to 10 atm in a piston-and-cylinder arrangement. Calculate the entropy change of the gas, the entropy change of the surroundings, and the total energy change resulting from the process, if: (a) the process is mechanically reversible and the surroundings consist of a heat reservoir at 127°C. (b) the process is mechanically reversible and the surroundings consist of a heat reservoir at 27°C. (c) the process...

A 10 cm -diameter cylinder contains argon gas at 10 atm pressure and a temperature of...

A 10 cm -diameter cylinder contains argon gas at 10 atm pressure and a temperature of 60 ∘C . A piston can slide in and out of the cylinder. The cylinder's initial length is 19 cm . 2600 J of heat are transferred to the gas, causing the gas to expand at constant pressure. 1-What is the final temperature of the cylinder? 2-What is the final length of the cylinder?

Subjects