Question

In: Civil Engineering

For these problems, assume air behaves as an ideal gas with R=0.287kJkgK. A compressor operates at...

For these problems, assume air behaves as an ideal gas with R=0.287kJkgK.

  1. A compressor operates at steady state and takes in air from ambient 0 kPa, gage and 200 K. The outlet pressure is 60 kPa, gage and 400 K. Determine:
    1. the mass flow rate if the inlet area is 20 cm2 and the inlet pressure is -5 kPa, gage.
    2. the minimum outlet temperature that is possible for this compressor.
    3. the isentropic efficiency of the compressor, assuming no heat loss.
    4. if there is a heat loss of 20 kJ/kg, the work required to run the compressor, and the new isentropic efficiency.

Solutions

Expert Solution

ANSWER:----

MASS FLOW RATE:--- The mass flow rate is the mass of a liquid substance passing per unit time. In other words, Mass flow rate is defined as the rate of movement of liquid mass through a unit area. The mass flow is directly depended on the density, velocity of the liquid and area of cross-section. It is the movement of mass per unit time.


Related Solutions

air behaves as an ideal gas with R = 0.287 k J k g K. A...
air behaves as an ideal gas with R = 0.287 k J k g K. A compressor operates at steady state and takes in air from ambient 0 kPa, gage and 300 K. The outlet pressure is 60 kPa, gage and 300 K. Determine: the mass flow rate if the inlet area is 10 cm2 and the inlet pressure is -3 kPa, gage. the minimum outlet temperature that is possible for this compressor. the isentropic efficiency of the compressor, assuming...
1) A gas turbine operates on an ideal Joule cycle using air (γ = 1.4; R...
1) A gas turbine operates on an ideal Joule cycle using air (γ = 1.4; R = 0.287 kJ/kg K) as working fluid. Air enters the compressor at temperature of 27◦C and pressure of 1.25 bar and is compressed to 7.6 bar. When the maximum cycle temperature is limited to 800 oC, calculate, (i) the thermal efficiency and work ratio of the cycle (ii) the temperature of air exiting the turbine and the change in specific entropy of turbine process...
. Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa...
. Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa and the turbine at 37oC and 170 kPa. The mass flow rate of air through the cycle is 0.3 kg/sec. Assuming variable specific heats for air, determine (a) the rate of refrigeration, (b) the net power input, and (c) the coefficient of performance. Also, draw the T-s diagram of the gas refrigeration cycle.
A gas turbine operates as a cold-air standard Brayton cycle. Air enetrs the compressor at 300K...
A gas turbine operates as a cold-air standard Brayton cycle. Air enetrs the compressor at 300K and 100kPa and is compressed to 700kPa. During the heat addition process in the combustor, the temperature of the air increases to 1000K. The turbine and compressor can be assumed to be operating isentropically. Evaluate specific heat at 300K. a. thermal efficiency of the cycle? b. net work of the cycle (kj/kg)? c. Back work ratio?
Air enters the compressor of an ideal gas refrigeration cycle at 17°C and 35 kPa and...
Air enters the compressor of an ideal gas refrigeration cycle at 17°C and 35 kPa and the turbine at 47°C and 160 kPa. The mass flow rate of air through the cycle is 0.3 kg/s. Assume variable specific heats for air. Determine the net power input. The net power input is kW.
3.70 kg / min of air as ideal gas enters a steady state compressor that runs...
3.70 kg / min of air as ideal gas enters a steady state compressor that runs adiabatically. Air enters P1 = 300 kPa and T1 = 440 K and exits at P2 = 500 kPa. If the isentropic efficiency of the turbine is 0.876, what is the work, in kW?
You are looking to purchase the DeWalt air compressor. Assuming the compressor operates (outputs) air at...
You are looking to purchase the DeWalt air compressor. Assuming the compressor operates (outputs) air at 90psi and at 110F. If the atmospheric pressure is 0 psig and the atmospheric temperature is 65F, how much free air will the compressor consume in cubic feet (ft3 )/Minute to handle the 5 standard cubic feet per minute (SCFM)? • DeWalt Specifications -- 1.6 HP electric engine gets the job done. High-pressure motor with consistent draw requirements can be run with a 12-Gauge...
An air engine is modeled after the ott cycle. Assume ideal gas and air standard cold...
An air engine is modeled after the ott cycle. Assume ideal gas and air standard cold valus for properties. Intake air is at 100kPa and Temperature of 27°C. The compression ration is 8:1. The heat added during ignition is 1740 kJ/kg a) Draw and Label the Pv and Ts diagrams for the Otto cycle b)Find the specific volume at intake state #1 c) Find the temperature at the end of the compression stroke d) Find the Pressure at the end...
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290...
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290 K with a mass flow rate (m⋅) of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (a) the thermal efficiency (ηth,Brayton) of the cycle. Use the PG model for air. (b) What-if Scenario: What would the thermal efficiency be if the regenerator effectiveness...
For the following, assume air is an ideal gas with constant specific heats at 300K. Find...
For the following, assume air is an ideal gas with constant specific heats at 300K. Find the work and heat transfer and state whether they are into or out of the air. In an open system, air is heated at constant pressure from 27°C, 400 kPa to 500K. w = 0 kJ/kg, q = 201 kJ/kg In a closed system, air is heated at constant pressure from 27°C, 100 kPa to 500K. w = 57.4 kJ/kg, q = 201 kJ/kg
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT