rapid sand filter will be constructed for average flow rate of 0.06 m3 / h. Design...

rapid sand filter will be constructed for average flow rate of 0.06 m3 / h.

Design (...find dimensions...) and draw the filter.

Expert Solution

Note in this calculation discharge is very less, so to obtained meaningfully results .. some standard value are taken less as compared to standard values.

le

Ally Wells answered 7 months ago

Design rapid sand filters for a water treatment plant to treat a flow rate of 25...

Design rapid sand filters for a water treatment plant to treat a flow rate of 25 mgd. Use 1.5 for a peak factor. Consider the location of overflow troughs, freeboard, and pressure head of water. Assume that the length of the filters is 2 times the width and that the filtration rate is 3 gpm/ft2. Assume anthracite over sand with 1 ft gravel under media, top of water level during filtration is below troughs, and a 3 ft head drop...

Pavement Design: New pavement design is to be constructed in 2026. The new average daily traffic...

Pavement Design: New pavement design is to be constructed in 2026. The new average daily traffic for commercial vehicles on the opening day will be 1700. Use: Growth rate = 6% Subgrade CBR = 3% Design life = 20 years

A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an...

A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an overflow rate of 4752 m3/m2 –d to capture sand with the following particle size distribution: % by wt. Diameter (mm) 30 1.0 30 0.5 30 0.2 10 0.1 The design overflow rate is such that 100% removal of the 0.5 mm diameter particles will be achieved. The operating temperature is 20°C and the specific gravity of the sand particles...

Determine the size of the high rate trickling filter for the following data: Sewage flow is...

Determine the size of the high rate trickling filter for the following data: Sewage flow is 5 MLD; Recirculation factor is 1.89; Raw wastewater BOD is 230 mg/L; BOD removed in PST is 30%; Final desired BOD in the treated effluent is 25 mg/L pls send the sol fast in rough only i need it urgent

A water tank consists of a cylindrical part of radius r and height h and a hemispherical top. The tank is to be constructed to hold 600 m3

A water tank consists of a cylindrical part of radius r and height h and a hemispherical top. The tank is to be constructed to hold 600 m3 when filled. The surface area of the cylindrical part is 2πrh, and its volume is πr2h. The surface area of the hemispherical top is given by 2πr2, and its volume is given by 2πr3/3. The cost to construct the cylindrical part of the tank is $400 per square meter of surface area;...

Volume of an activated sludge tank 12. The total design flow is 15,000 m3/day. The NPDES...

Volume of an activated sludge tank 12. The total design flow is 15,000 m3/day. The NPDES limit is 25/30. Assume that the waste strength is 170 mg/L BOD after primary clarification. Y = 0.55 kg/kg, X=MLSS = 2200 mg/L, XR = 6,600 mg/L, Recycle (R) = 0.25, kd = 0.05 day -1, qc = 8 days Make whatever other assumptions are needed. The volume the tank in m3 will be?

Water flows in a horizontal pipeline at a steady flow rate of 0.03 m3 s-1. The...

Water flows in a horizontal pipeline at a steady flow rate of 0.03 m3 s-1. The pipeline terminates with a reducing bend that deflects the water upwards at an angle of 45 degrees, as shown in Figure QB2. The water issues into the atmosphere. The area of the pipe is 150 x 10-4 m2 and the area at the exit to the bend is 25 x 10-4 m2. The gauge pressure at the inlet to the bend is 73.9 kN...

Consider a 10x108 m3 lake fed by a polluted stream having a flow rate of 2.0...

Consider a 10x108 m3 lake fed by a polluted stream having a flow rate of 2.0 m3 /s and pollutant concentration equal to 10.0 mg/L. There is also a sewage outfall that discharges 0.5 m3 /s of wastewater that has a pollutant concentration of 100 mg/L into the lake. The stream and sewage pollutants have a decay rate coefficient of 0.20 day-1 (first order). Under these flow conditions the lake remains the same volume (e.g. a stream enters and exits...

A lined canal (n = 0.016) is designed to carry a flow rate of 33 m3/s....

A lined canal (n = 0.016) is designed to carry a flow rate of 33 m3/s. The canal is laid at a slope of 14 cm/km with a side slope of 2:1. Design the canal cross section (the water depth and bed width) according to each of the following scenario: If Velocity is 1.0 m/s If the Most efficient hydraulic section (i.e., when Rh=y/2) If Width/depth =5 Comment on the practicality of the designs (Height of side slope, flow velocity,...

1. Design 3rd order ideal low pass filter H(s). Two poles are complex conjugates, and one...

1. Design 3rd order ideal low pass filter H(s). Two poles are complex conjugates, and one pole is on the real axis. 2. transform H(s) to H(z). (Use impulse invariance criterion) 1%criterion

Question