Question

In: Civil Engineering

Q3. Flow velocity of wastewater approaching a Grit chamber is 10cm/s. Design the grit chamber with...

Q3. Flow velocity of wastewater approaching a Grit chamber is 10cm/s. Design the grit chamber with appropriate Free board and a proportionate flow weir at its outlet to handle a sewage flow from a Population of 44,000 with a per capita water consumption of 250 liters/day. It has to handle maximum flow 2 times the average flow. Depth = 1.5m
Length of grit chamber is limited to 8m and it cannot hold water more than 1.5 minutes.

Solutions

Expert Solution


Related Solutions

A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an...
A grit chamber is designed to treat an average wastewater flow of 1 m3/sec at an overflow rate of 4752 m3/m2 –d to capture sand with the following particle size distribution:          % by wt.                        Diameter (mm)                30                                         1.0                30                                         0.5                30                                         0.2                10                                         0.1 The design overflow rate is such that 100% removal of the 0.5 mm diameter particles will be achieved. The operating temperature is 20°C and the specific gravity of the sand particles...
a constant velocity horizontal flow grit channel is discharging unacceptable amounts of grit into the primary...
a constant velocity horizontal flow grit channel is discharging unacceptable amounts of grit into the primary facultative pond of a stabilization pond. In addition the channel overtops regularly with peak wet weather flow during normal rain storms. An initial investigation confirmed levels of grit present in the particular wastewater to be within normal loading levels. Furthermore, the provision for grit storage capacity in the channel is adequate for the operational cleaning-out cycle employed. According to the authorities, the likely cause...
Q3. You have been selected to design a secondary wastewater treatment plant for a municipality in...
Q3. You have been selected to design a secondary wastewater treatment plant for a municipality in Amman of 15,000 people which has some industry that discharges wastewater to the municipal sewer system. The average daily wastewater flow is 2.1 MGD (million gallon/d) and the raw sewage entering the WWTP has an average BOD5 of 240 mg/L and average suspended solids of 260 mg/L. If the average domestic per capita sewage flow is 115 gpcd, what is the average flow of...
An air–fuel mixture enters a constant area combustion chamber at a velocity of 100 m/s a...
An air–fuel mixture enters a constant area combustion chamber at a velocity of 100 m/s a pressure of 70 kPa and a temperature of 150°C. Assuming that the fuel–air ratio is 0.04, the heating value of the fuel is 30 MJ/kg, and the mixture has the properties of air, calculate the Mach number in the gas flow after combustion is completed and the change of stagnation temperature and stagnation pressure across the combustion chamber. Neglect the effects of viscosity and...
calculate the maximum velocity and the correspondingbvolumetric flow rate (in/cm^3/s) at which laminar flow of air...
calculate the maximum velocity and the correspondingbvolumetric flow rate (in/cm^3/s) at which laminar flow of air and water is possible in pipes with the following diameter D=.25,.5,1.0,2.0,4.0,6.0, and 10.0in
A stream has a temperature of 20 degrees C, a velocity of 0.5 m/s, a flow...
A stream has a temperature of 20 degrees C, a velocity of 0.5 m/s, a flow rate of 3.0 m3/s, depth of 3.0 m, saturation dissolved oxygen (DO = 9.07 mg/L), and BODu = 5 mg/L. Assume the deoxygenation constant (k) = 0.24 d-1. Wastewater discharge flows into the stream at 0.6 m3/s and temperature of 20 degrees C, and the DO is 8.1 mg/L. The lowest DO downstream is 4.0 mg/L and it occurs at a distance of 20...
The average flow velocity is 0.305 m/s. At the source, the BOD concentration is 10.0 mg/L...
The average flow velocity is 0.305 m/s. At the source, the BOD concentration is 10.0 mg/L and the dissolved oxygen deficit is 0.0 mg/L. From field sampling, de-oxygenation (kd) and re-aeration (ka) rate constants are estimated to be 0.6 d-1 and 2.0 d-1, respectively. Find the critical distance, the critical deficit, and the time at which the minimum D.O. occurs
Design a two-phase vertical separator for gas flow rate 25ft 3 /s and oil flow rate...
Design a two-phase vertical separator for gas flow rate 25ft 3 /s and oil flow rate 3000 ft 3 /s. The operating conditions P=1000 Pisa, T=90 O F, Z=0.85, dm=150 micron, µ= 0.013 cp and liquid residence time=3min. Where: Liquid density =50 Ib/ ft 3 Gas density=5 Ib/ ft
An axial flow fan 1.83 m diameter is designed to run at a speed of 1400 rev/min with an average axial air velocity of 12.2 m/s
An axial flow fan 1.83 m diameter is designed to run at a speed of 1400 rev/min with an average axial air velocity of 12.2 m/s. A quarter scale model has been built to obtain a check on the design and the rotational speed of the model fan is 4200 rev/min. Determine the axial air velocity of the model so that dynamical similarity with the full-scale fan is preserved. The effects of Reynolds number change may be neglected. A sufficiently large...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT