Question

In: Computer Science

Memory organization: For a memory consisting of 32 modules, each with a capacity of 1M x...

  1. Memory organization:
    1. For a memory consisting of 32 modules, each with a capacity of 1M x 8 bits (here a basic memory storage unit is a byte or 8 bits), how many bits are needed to represent each address that is uniquely associated with each basic storage unit?
    2. For this memory system, if high-order interleaving is used, what is the address structure (i.e., what bits are used to select the chip and what bits are used to identify the offset within the chip.)
    3. For the same memory system, what is the address structure if low-order interleaving is used?
  1. Memory organization: Repeat procedure a), b), and c) above for a different memory system consisting of 4 modules, each with a capacity of 4G x 16 bits.

Solutions

Expert Solution


Related Solutions

Suppose we have 4 memory modules and each module has 8 addresses. Draw the memory modules...
Suppose we have 4 memory modules and each module has 8 addresses. Draw the memory modules with the addresses they contain using: a) High-order Interleaving and b) Low-order interleaving.
Design a 64M x 64-bit memory using 16M x 16-bit memory modules.
Design a 64M x 64-bit memory using 16M x 16-bit memory modules.
What is the structure of memory and the capacity and duration of each part? Sensory memory...
What is the structure of memory and the capacity and duration of each part? Sensory memory Short-termmemory(STM) Long-term memory(LTM)
What is the structure of memory and the capacity and duration of each part?
What is the structure of memory and the capacity and duration of each part?
a) The capacity of a memory chip is specified as 64K x 8 bits. Find out...
a) The capacity of a memory chip is specified as 64K x 8 bits. Find out the address lines & the data lines for the chip. b) A memory block has 20 address lines & 16 data lines. Specify its capacity c) Assume a 32-bit microprocessor is to be used in a computer system, what is the size of its address bus, data bus, control bus and the registers if it needs to access up to 32GB of data? Assume...
Assume that the variables w, x, y, and z are stored in memory locations 16, 32,...
Assume that the variables w, x, y, and z are stored in memory locations 16, 32, 48, and 128 respectively. Translate the following algorithmic operations into MIPS language equivalents: [Assume $s1 is the base register, and $s1 contains the address of memory location 0]                                                                                                             if ((x – y) ³ w) then       set x to y else: set x to z endif
1.) Define Memory 2.) Define each (Capacity and duration/time):    a. sensory memory    b. short-term...
1.) Define Memory 2.) Define each (Capacity and duration/time):    a. sensory memory    b. short-term memory    c. long-term memory 3.) Describe the process of information going through these three memory stages.
You are given 1 liter of each of the following solutions: 1M HCl, 1M NaOH, 1M...
You are given 1 liter of each of the following solutions: 1M HCl, 1M NaOH, 1M NH3 , 1M HC2H3O2 , 1MNH4Cl, 1MNaC2H3O2 a) Describe 4 different methods for preparing a buffer solution b) Describe how you would prepare 400 ml a buffer with a pH= 4.74 and a buffer with pH= 9.25 c) Draw titration curves for : strong acid-strong base, strong acid-weak base, strong base-weak acid. Label the graph axes, indicate initial pH and pH at equivalence.   
Discuss how working memory is a limited capacity system. Discuss the three components of working memory...
Discuss how working memory is a limited capacity system. Discuss the three components of working memory (phonological loop, visuospatial sketch pad, and the central executive List examples of everyday tasks that may create overload problems.
Each group will have a stock solution of 1M acetic acid and 1M sodium acetate. 2....
Each group will have a stock solution of 1M acetic acid and 1M sodium acetate. 2. Prepare 22mL buffer solution with 0.35M acetic acid and 0.35M sodium acetate. Given that the Ka of acetic acid is 1.8 x 10-5. What is the expected pH of the buffer? 3. Pipette the prepared buffer solution into two clean containers, each with 10mL buffer solution. Calculate and measure how the pH change if a. 2mL 0.025M NaOH is added to tube 1. b....
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT