STEEL STRUCTURES A 20ft long simply supported beam is made of W21X55 with fy=50ksi. The service...

STEEL STRUCTURES

A 20ft long simply supported beam is made of W21X55 with fy=50ksi. The service distributed loads on the beam are DL=2k/ft (including self weight), LL=4 k/ft. Show if the beam is adequate for shear.

Solutions

Expert Solution

Ally Wells answered 3 months ago

Next > < Previous

Related Solutions

Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and...

Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and subjected to a point load at the midspan. The point service load consists of 60% live load and 40% dead load. Lateral supports exist at the ends only. Design code to comply with: 2016 AISC LRFD. (a) Determine the maximum point service load P for strong-axis bending assuming Cb = 1.0. (b) Redetermine the maximum point service load P for strong-axis bending considering proper...

(1) A simply supported steel beam is 30' long and subjected to a uniform distributed 1.3...

(1) A simply supported steel beam is 30' long and subjected to a uniform distributed 1.3 kips per foot. What is the minimum required section modulus for this beam if we do not want its maximum stress to exceed 50 ksi? (2) What is the minimum inertia of the beam in the previous question if we do not want it to deflect more than 1/2" ?

A 14ft long simply supported beam of A992 steel is laterally braced only at its ends....

A 14ft long simply supported beam of A992 steel is laterally braced only at its ends. It has a uniformly distributed dead load of 2k/ft. and uniformly distributed live load of 3k/ft. Determine: Size based on bending. determine Factored loads, bending moment, Determine Allowable Bending Moment based on Lb compare actual to allowable check deflection with 5wL4/384EI Check Shear determine Maximum shear Vu compare to allowable .6FyAwCv

A beam 3m long is simply supported at its ends. The beam is loaded with a...

A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. USING AMM. a.) The maximum deflection is located at what distance from the left support? Answer: 1.63m b.) Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4 Answer 2.9mm

A beam 3m long is simply supported at its ends. The beam is loaded with a...

A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. Using DIM: a. The maximum deflection is located at what distance from the left support? b. Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4

This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported...

This question is referring to a concrete beam with steel rebar reinforcement, For a simply supported beam with width 10 inches and depth 14 inches design the steel to resist a maximum moment of 50 kip feet. span=15 feet. Concrete 4 ksi. steel is 60 ksi.

A simply supported beam with a span of 26 FT is used to carry a service...

A simply supported beam with a span of 26 FT is used to carry a service dead load (including self-weight) of 1.65 KLF and a service live load of 3.3 KLF and is reinforced with 4-#9 bars. The beam has a width b of 14 IN, an effective depth of 24.5 IN., and a height of 27 IN. The material strengths are f’c = 4000 PSI and fy = 60 KSI. The immediate deflection due to live load is limited...

What are the problems arised in simply supported beam bridge(any component of the bridge or steel...

What are the problems arised in simply supported beam bridge(any component of the bridge or steel trusses type) and how to improve the qualities or the problems arised?

A simply supported beam has a width of 200mm and depth of 400mm is 4m long....

A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and...

2. A simply supported rectangular concrete beam is to be made from M21 concrete grade and reinforced with steel bar of 345 MPa yield strength. It carries a uniformly distributed load of 12.5 kN/m and has a span of 6 m. Design the beam, assuming that the shape factor is 0.4. The weight density of steel is 77 kN/m3 and that of concrete is 24 kN/m3.

Subjects