Choose the correct answer from the followings: a) In Wheatstone bridge, when it is balanced the...

Choose the correct answer from the followings:

a) In Wheatstone bridge, when it is balanced the galvanometer reads

1. Inﬁnity 2. Zero 3. 5 mA 4. 10 mA
b) In PMMC, dumping force helps .............

1. To move the pointer to read our measurements correctly 2. To reset our readings back to zero 3. To stabilize the pointer during transition between readings 4. All the above
c) A current transformers are used for:

1. For cost eﬀective measurement 2. For protections 3. To reduce the cost of relay and circuit-breaker in high current enviroemnt 4. All the above

Expert Solution

If you have any doubt ask me if understand please upvote answer thank you

Manojponduru answered 10 months ago

What is the balanced condition of Wheatstone Bridge circuit?

In the event that the Wheatstone Bridge is NOT level (balanced), can the Series circuit be...

In the event that the Wheatstone Bridge is NOT level (balanced), can the Series circuit be resolved? Can it be solved in parallel? What method would you use?

Choose the most correct answer The LVDT is connected with deflection bridge for displacement and pressure...

Choose the most correct answer The LVDT is connected with deflection bridge for displacement and pressure measurement True False In real work life, the accelerometer signal is integrated twice to obtain the displacement True False The vortex flow meter measures the flow rate based on ultrasonic sensor True False A force measurement system with range 0-1000 N, linearity error=0.1% FSO, Hysteresis error=0.1% FSO, repeatability error=0.15% FSO, and zero drift=0.2% FSO, then the overall instrument error is 5.1% 0.63% 0.29%

Choose the correct answer: 1)) An annually balanced budget a is the surest path to economic...

Choose the correct answer: 1)) An annually balanced budget a is the surest path to economic stability b is required by the U.S. Constitution c dampens cyclical swings by decreasing government spending during expansions and increasing it during recessions d accentuates cyclical swings by increasing government spending during expansions and reducing it during recessions e is a goal that has only been achieved twice in the past 5 years 2)) Approximately what percentage of the U.S. federal budget was used...

Design a system to measure bending strain using a full-bridge wheatstone bridge configuration.

The circuit shown in the figure below, called the Wheatstone bridge, is used to determine the...

The circuit shown in the figure below, called the Wheatstone bridge, is used to determine the value of unknown resistor Xby comparison with three resistors M, N, and P whose resistances can be varied. For each setting, the resistance of each resistor is precisely known. With switches K1 and K2 closed, these resistors are varied until the current in the galvanometer G is zero; the bridge is then said to be balanced. (a) Show that under this condition the unknown...

What are the advantages of Wheatstone bridge measurement over a direct resistance measurement if for a...

What are the advantages of Wheatstone bridge measurement over a direct resistance measurement if for a temperature sensor?

please provide an example of a wheatstone bridge circuit in a HALF brindge as well as...

please provide an example of a wheatstone bridge circuit in a HALF brindge as well as a FULL bridge with hand calculations.

Choose the correct answer. A.1. The paradox of sparing: A. occurs when the increase in savings...

Choose the correct answer. A.1. The paradox of sparing: A. occurs when the increase in savings leads to a reduction in total expenditure. B. occurs when the increase in consumption leads to a reduction in total expenditure. C. is a result of fiscal policy. D. is a result of monetary policy. A.2. The productive gap of the economy: A. occurs when monetary policy is effective. B. occurs when fiscal policy is effective. C. is the deviation of real GDP from...

Using a wheatstone bridge, solve for Vout for quarter, half, and full bridges and determine which...

Using a wheatstone bridge, solve for Vout for quarter, half, and full bridges and determine which one is most sensitive. Draw a diagram showing how you would place your strain gauges on a beam for each configuration. Discuss how you should use the right kind of strain gauge with appropriate G values to maximize the sensitivity.

Question