Question: Using the data obtained from the uniaxial compressive strength test given below: a. Find the...

Question: Using the data obtained from the uniaxial compressive strength test given below:

a. Find the average uniaxial compressive strength (UCS) and standard deviation.

b. Make UCS classification (ISRM, 1978).

Specimen Diameter (mm)	Specimen Height (mm)	Failure Load (kN)
54,0	140	252,5
53,2	135	275,5
53,7	140	232,5
53,5	130	225,5
53,1	135	217,5
53,2	140	225,5

Expert Solution

a)

b)

Hope this helps,

Please free to comment for any further queries,

All the best

Ally Wells answered 1 year ago

in table 1 the failure load obtained from the compressive strength test at the laboratory are presented....

in table 1 the failure load obtained from the compressive strength test at the laboratory are presented. sate whether those values are satisfactory according to TS EN206 1;2004 or not verify your results. concrete class C35. Determine also standard deviation and variance Table 1 Failure load for 200 mm cubic samples NO FAILURE LOAD (KN) 1 1645 2 1646 3 1641 4 1641 5 1641 PLEASE CAN YOU SLOVE IT STEP BY STEP

The accompanying data was obtained in an experiment to investigate whether compressive strength of concrete cylinders...

The accompanying data was obtained in an experiment to investigate whether compressive strength of concrete cylinders depends on the type of capping material used (factor A) or variability in different batches (factor B). Each number is a cell total (xij.) based on K = 3 observations. Batch 1 2 3 4 5 Capping Material 1 1844 1941 1934 1888 1799 2 1778 1850 1793 1785 1626 3 1804 1892 1890 1890 1758 In addition, ΣΣΣxijk2 = 16,806,946 and ΣΣxij.2 =...

A random sample from a normal population is obtained, and the data are given below. Find...

A random sample from a normal population is obtained, and the data are given below. Find a 90% confidence interval for . 114 157 203 257 284 299 305 344 378 410 421 450 478 480 512 533 545 What is the upper bound of the confidence interval (round off to the nearest integer)?

Using the compressive stress-strain data provided in fig below and the Australian standard AS 1012.17 test...

Using the compressive stress-strain data provided in fig below and the Australian standard AS 1012.17 test method for determining the modulus of elasticity of concrete, determine the modulus of elasticity of concrete for the following two scenarios: a. concrete requiring complete hydration f the Portland cement and minimal porosity b. Concrete that will simulate equivalent workability to the concrete mix listed in bullet point (a) but with HWR added to the mix to maximize the plasticising effect

Problem from statistic The data below are from a 25-question test given to 20 students. The...

Problem from statistic The data below are from a 25-question test given to 20 students. The values indicate the number of questions answered correctly in each test. 10 11 11 13 13 13 14 15 15 16 16 16 16 16 18 18 18 19 19 19 Summarize the data by computing the frequency distribution and the percentage frequency distribution. Use the following class intervals (left end point convention): Class 1 2 3 4 Class interval 10-13 13-15 15-17 17-20...

Strength of concrete: The compressive strength, in kilopascals, was measured for concrete blocks from five different...

Strength of concrete: The compressive strength, in kilopascals, was measured for concrete blocks from five different batches of concrete, both three and six after pouring. The data are as follows. Can you conclude that the mean strength after three days is less than the mean strength after six days? Let U1 represent the mean strength after three days and ud=u1-u2, Use the a=0.01 level and the critical value method with the table. 1. State the appropriate null and alternate hypotheses....

Strength of concrete: The compressive strength, in kilopascals, was measure for concrete blocks from five different...

Strength of concrete: The compressive strength, in kilopascals, was measure for concrete blocks from five different batches of concrete, both three and six days after pouring. The data are as follows: Block 1 2 3 4 5 After 3 days 1341 1316 1352 1355 1327 After 6 days 1376 1373 1366 1384 1358 Can you conclude that the mean strength after three days differs from the mean strength after six days? Use the α = 0.05 level of significance. State...

Question 1: A small data set is given below. You will run a t-test using Excel....

Question 1: A small data set is given below. You will run a t-test using Excel. In order to receive full credit, you must turn in Excel output and your final answers. Round off final answers to three decimal places, if appropriate. A medical researcher wants to determine whether a drug changes the body’s temperature. Seventest subjects are randomly selected, and the body temperature (in degrees Fahrenheit) of each is measured. The subjects are then given the drug and after...

The following are 13 observations on burst strength (lb/in2) obtained from a test on a certain...

The following are 13 observations on burst strength (lb/in2) obtained from a test on a certain type of closure weld. 5900, 6200, 6700, 7200, 7200, 7300, 7300, 7300, 7400, 7400, 7600, 8200, 8300 a. Give the five–number summary of this distribution. b. Are there any suspected outliers in the data? If so, which values? (Remember to use the IQR formula for determining the existence of outliers.) c. From your answer above, create a boxplot for the data and mark/label all...

The data in the accompanying table represent the compressive strength, in thousands of pounds per square...

The data in the accompanying table represent the compressive strength, in thousands of pounds per square inch (psi), of 20 samples of concrete taken two and seven days after pouring. Sample Two days Seven days 1 3.205 3.54 2 2.855 3.355 3 3.135 3.605 4 3.425 4.03 5 3.16 3.43 6 3.765 4.57 7 2.68 3.805 8 3.315 3.685 9 3.205 3.59 10 3.605 3.72 11 2.895 3.25 12 3.08 3.14 13 3 4.005 14 3.035 3.595 15 2.27 3.91...

Question