Question
In: Civil Engineering
2: Results obtained from a tension test on a bar of uniform cross section 10 mm...
2:
Results obtained from a tension test on a bar of uniform cross
section 10 mm x 10 mm subjected to an axial pull of 8000 N were
tabulated. The lateral dimensions of the bar were found to be
changed to 9.9985 mm x 9.9985 mm while using a material having
modulus of rigidity equal to 0.8 x 107 N/cm2. By determining the
values for different moduli, identify the properties of material
and establish the relationship between them. What changes will
happen to the volume if the length of the bar is equal to 2.5 m?
Based on the results obtained discuss how the elastic constants are
related to the deformation of the bar?
Solutions
Ally Wells answered 10 months agoRelated Solutions
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of
uniform cross section 10 mm x 10 mm subjected to an axial pull of
8000 N were tabulated. The lateral dimensions of the bar were found
to be changed to 9.9985 mm x 9.9985 mm while using a material
having modulus of rigidity equal to 0.8 x 107 N/cm2. By determining
the values for different moduli, identify the properties of
material and establish the relationship between them. What changes
will...
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of uniform cross
section 10 mm x 10 mm subjected to an axial pull of 8000 N were
tabulated. The lateral dimensions of the bar were found to be
changed to 9.9985 mm x 9.9985 mm while using a material having
modulus of rigidity equal to 0.8 x 107 N/cm2. By determining the
values for different moduli, identify the properties of material
and establish the relationship between them. What changes will...
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of uniform cross
section 10 mm x 10 mm
subjected to an axial pull of 8000 N were tabulated. The lateral
dimensions of the bar were found
to be changed to 9.9985 mm x 9.9985 mm while using a material
having modulus of rigidity equal
to 0.8 x 107 N/cm2. By determining the values for different moduli,
identify the properties of
material and establish the relationship between them. What changes
will...
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of
uniform cross section 10 mm x 10 mm subjected to an axial pull of
8000 N were tabulated. The lateral dimensions of the bar were found
to be changed to 9.9985 mm x 9.9985 mm while using a material
having modulus of rigidity equal to 0.8 x 107 N/cm2. By determining
the values for different moduli, identify the properties of
material and establish the relationship between them. What changes
will...
Consider an electron beam of uniform circular cross-section with a diameter of 1 mm. The electrons...
Consider an electron beam of uniform circular cross-section with
a diameter of 1 mm. The electrons are accelerated from the cathode
to the anode, which are separated by 1 m. The electrons are
generated at the cathode and therefore have negligible velocity at
this position. The electrons accelerate at a rate of 108 ?/?2
between the cathode and anode. The current density at the anode is
104 ?/?2 .
Find the current density as a function of position between the...
A 2.8 mm -diameter copper wire carries a 31 Acurrent (uniform across its cross section). A)...
A 2.8 mm -diameter copper wire carries a 31 Acurrent (uniform
across its cross section).
A) Determine the magnetic field at the surface of the wire.
B) Determine the magnetic field inside the wire, 0.50 mm below
the surface.
C) Determine the magnetic field outside the wire 2.5 mm from the
surface.
10 cm of copper with square cross section of 1x1 cm exposed to 200 KN tension...
10 cm of copper with square cross section of 1x1 cm exposed to
200 KN tension force
caused 15% permanent reduction in cross section area , if
the fracture got on this point,
calculate the following:
1 – the ductility
2 – stress
3 – true stress
4- fracture stress
A bar with an equilateral triangle cross section experienced a strain of 6.5983 x 10-4 due...
A bar with an equilateral triangle cross section experienced a
strain of 6.5983 x 10-4 due to an axial load of 2 kN. The
dimensions of the cross section is 5 mm and the length is 300 mm.
Assume that the poisson’s ratio is 0.28.
What is the value of the modulus of elasticity in GPa? Ans =
280 GPa
What is the value of the modulus of rigidity in GPa? Ans =
109.38 GPa
What is the bulk modulus...
The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm.
The steel beam has the cross section shown. The beam length is L = 6.9 m, and the cross-sectional dimensions are d = 345 mm, bf = 185 mm, tf = 15 mm, and tw = 10 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 185 MPa.
A bar of n-type Si with a cross-sectional area of 1 mm x 1 mm and...
A bar of n-type Si with a cross-sectional area of 1 mm x 1 mm
and a length of 1 cm is connected to a 2 V battery and is carrying
a current of 2 mA at 300 K. (a) Calculate the thermal equilibrium
electron and hole concentrations in the bar. (b) Calculate the
dopant concentration assuming that only donors with energy level
0.148 eV away from the conduction band are present. (c) Determine
the temperature at which the bar...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- C & S Department Store is the second largest clothing and retail store chain in Jamaica....
- Will the Internet and related communication technologies be tools for increasing political freedom, or will they...
- Design a rectangular tied column for a DL = 1000 KN and a LL = 1350...
- Using the Stack class (it's on the class web page) construct a program that will evaluate...
- An old two-flat can be purchased for $200,000 cash. The two units can bring in a...
- Please code in C# - (C - Sharp) Assignment Description Write out a program that will...
- Geraldine Wolfe is a supervisor at Fantastigifts. She has an annual salary of $45,500, paid biweekly,...
ADVERTISEMENT