Question

In: Civil Engineering

For the column and beam layout, find the required slab thickness and spacing of #4 reinforcing...

For the column and beam layout, find the required slab thickness and spacing of #4 reinforcing bars, if the loading in addition to self-weight, is 2 point loads of 2 kips at the third points of each span (4 point loads total) f'c =4000psi fy = 60ksi d = hSLAB - 1in,
weight of reinforced concrete is 150pcf, width of beams - 12in, space between borders of beams - 7ft.

Solutions

Expert Solution

The below design of slab is based upon IS 456-2000,

a) Effective span of slab:

Effective span of slab shall be lesser of the two

1. L=Clear span+ d (Effective depth)

2. L=Center to center distance between the support

b) Depth of slab:

The depth of slab depends on bending moment and deflection criterion. The trail depth can be obtained using:

1. Effective depth d= Span/((L/d)basic X modification factor)

2. For obtaining modification factor, the percentage of steel for slab can be assumed from 0.2 to 0.5%.

3. The effective depth d of two way slabs can also be assumed using cl.24.1, IS 456 provided short span is <3.5m and loading class is <3.5 kN/m2.

Type of support for simply supported Fe-415 slab= L/28

Or, the following thumb rules can be used:

1. One way slab d=(L/22) to (L/28)

2. Two way simply supported slab d=L/20) to (L/30)

Two way restrained slab d=(L/30) to (L/32)

c) Loads on slab:

The load on slab comprises of dead load, floor finish and live load.The loads are calculated per unit area (load/m2)

Dead load D X 25 kN/m2 (Where D is thickness of slab in m)

Floor finish (Assumed as)= 1 to 2 kN/m2

Live load (Assumed as)= 3 to 5 kN/m2 (depending on the occupancy of the building)

Detailing requirements of reinforced concrete slab as per IS45:2000

a) Nominal cover:

For mild exposure- 20mm

For moderate exposure- 30mm

However, if the diameter of bar do not exceed 12mm, or cover may be reduced by 5mm. Thus for main reinforcement up to 12mm diameter bar and for mild exposure, the nominal cover is 15mm.

b) Minimum reinforcement:

The reinforcement in either direction in slab shall not be less than

1) 0.15% of the total cross sectional area for Fe-250 steel

2) 0.12% of the total cross-sectional area for Fe-415 & Fe-500 steel.

c) Spacing of bars:

The maximum spacing of bars shall not exceed

1) Main steel- 3d or 300 mm whichever is smaller

2) Distribution steel- 5d or 450 mm whichever is smaller. Where, d is the effective depth of slab.

Note: The minimum clear spacing of bars is not kept less than 75 mm (Preferably 100 mm ) though code do not recommend any value.

d) Maximum diameter of bar:

The maximum diameter of bar in slab, shall not exceed D/8, where D is the total thickness of slab.


Related Solutions

For the column and beam layout, find the required slab thickness and spacing of #4 reinforcing...
For the column and beam layout, find the required slab thickness and spacing of #4 reinforcing bars, if the loading in addition to self-weight, is 2 point loads of 2 kips at the third points of each span (4 point loads total) f'c =4000psi fy = 60ksi d = hSLAB - 1in, weight of reinforced concrete is 150pcf, width of beams - 12in, space between borders of beams - 7ft.
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a...
Determine the required shear reinforcing for a simply supported concrete beam 7 meters long with a cross section of 500 millimeters in depth and a width of 380 millimeters. Use fc = 35 MPa fy = 400 MPa. The longitudinal steel uses one row of 25M bars. The specific live load is 29 kKn/m. The beam is not exposed.
What thickness of lead is required to attenuate a broad beam of 500 keV photons to...
What thickness of lead is required to attenuate a broad beam of 500 keV photons to one half of the original number (with better than 5% precision) ? Hint: use buildup factors for this poor geometry.
Find the required amount of reinforcement required for the abdominium beam in order to support the...
Find the required amount of reinforcement required for the abdominium beam in order to support the cross-sectional bending moment MU= 525 kN·m under the counting load. Design cover thickness 40mm and stub reinforcement using D10. Compressed iron bars do not have to be surrendered, and the size of the cross-section can only be increased if the design is not possible under the given conditions. b = 320 mm, h = 550 mm, fck = 32 MPa, fy= 450 MPa, Using...
Find the required rectangular cross-sectional area for a tied reinforced concrete column which should support a...
Find the required rectangular cross-sectional area for a tied reinforced concrete column which should support a load of 300 tons. Use 4000 psi concrete, ultimate steel stress of 60,000 psi and 4% steel.
4) Interest (Show all of your work!) Find the interest rate required for an investment of...
4) Interest (Show all of your work!) Find the interest rate required for an investment of $10,000 to grow to $15,000 in 5 years if the interest is compounded as follows: a) Annually b) Quarterly 5) Inflation (Show all of your work!) Assuming annual compounding, find the time it would take for the general level of prices, in the economy, to double at the following annual inflation rates: a) 3% b) 8% 6) Time to Double (Show all of your...
Evaluate the required second order partial derivative. Find fyx(4, -1), if f(x, y) = -4x3y2 +...
Evaluate the required second order partial derivative. Find fyx(4, -1), if f(x, y) = -4x3y2 + 2x4 - 3xy3. Group of answer choices 759 768 375 502
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT