Question

In: Electrical Engineering

what are: bus extensions? bus bar? bus raiser? bus section?

what are:
bus extensions?
bus bar?
bus raiser?
bus section?

Solutions

Expert Solution

Bus Extesion: Bus Extension is data bus that help to extend the reach of data to end node. for ex. The internal information bus extension is used to increase a fieldbus node and primarily consists of an internal data bus extension finish module and a minimum of one and up to 10 internal data bus extension coupling modules.

BusBar: In electrical power distribution, a busbar (also bus bar, and generally misspelled as buss bar or bussbar) is a metallicstrip or bar, typically housed within switchgear, panel boards, and busway enclosures for local high current power distribution. they're also used to connect high voltage instrumentation at electrical switchyards, and low voltage instrumentation in battery banks.

Bus Riser: Bus riser is a set of bus bar that connected from the coupling breakers, outgoing section enclose within the panel and connected to your incoming one or incoming a pair of bus bar section. It rely that side is your outgoing from the bus bar coupler breakers or depend upon your electrical style.

Bus riser is used in between 2 buses at same level connected with a fuse known as bus coupler.In this system one bus is connected with higher portion of the breaker and lower portion or output of fuse is connected to bus riser who works to rise the bus on level of 1st one.

Bus Section: The bus section is used in switchgear having one conductor Configuration to divide the bus into 2 Sections. i.e Bus section is section between single bus ( bus section is mean section A and B)


Related Solutions

6. A 30 MVA generator with 15% reactance is connected to a bus bar. A 25...
6. A 30 MVA generator with 15% reactance is connected to a bus bar. A 25 MVA transformer with 10% reactance is also connected through a 10% bus bar reactor to the same bus bar. Both of these reactance is based on 25 MVA. If a feeder taken out from the bus bars through a circuit breaker develops a three-phase fault, what should be the appropriate rating of the circuit breaker? 7. A system operates at 220 kVA and 11...
What is a BUS and what are different 'named' uses for the bus, and what do...
What is a BUS and what are different 'named' uses for the bus, and what do the CPU and RAM and the BUS have in common.. give two different examples.
What is a product? What is a brand? Critically explain the differences between line extensions, category...
What is a product? What is a brand? Critically explain the differences between line extensions, category lines, and brand extensions? Support your answers with marketing examples. (2.5 pages maximum)
What acknowledgment signals are there in I2C bus?
What acknowledgment signals are there in I2C bus?
What extensions to other mathematics and real world applications does Group Cohomology have?
What extensions to other mathematics and real world applications does Group Cohomology have?
A bar with an equilateral triangle cross section experienced a strain of 6.5983 x 10-4 due...
A bar with an equilateral triangle cross section experienced a strain of 6.5983 x 10-4 due to an axial load of 2 kN. The dimensions of the cross section is 5 mm and the length is 300 mm. Assume that the poisson’s ratio is 0.28. What is the value of the modulus of elasticity in GPa? Ans = 280 GPa What is the value of the modulus of rigidity in GPa? Ans = 109.38 GPa What is the bulk modulus...
Lab Procedure The cross-section dimensions of the 6061-T6 aluminum bar are 0.512 in x 0.248 in....
Lab Procedure The cross-section dimensions of the 6061-T6 aluminum bar are 0.512 in x 0.248 in. Attach the lead wires of the gages to the strain indicator as a quarter bridge circuit. (Note: the black and white lead wires are the common leads.) Enter the gage factor (GF=2.11) into the strain indicator. Record the specimen number (1, 2, or 3). Balance the strain indicator and note the zero readings. Load the specimen according to the table below and record the...
2: Results obtained from a tension test on a bar of uniform cross section 10 mm...
2: Results obtained from a tension test on a bar of uniform cross section 10 mm x 10 mm subjected to an axial pull of 8000 N were tabulated. The lateral dimensions of the bar were found to be changed to 9.9985 mm x 9.9985 mm while using a material having modulus of rigidity equal to 0.8 x 107 N/cm2. By determining the values for different moduli, identify the properties of material and establish the relationship between them. What changes...
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of uniform cross section 10 mm x 10 mm subjected to an axial pull of 8000 N were tabulated. The lateral dimensions of the bar were found to be changed to 9.9985 mm x 9.9985 mm while using a material having modulus of rigidity equal to 0.8 x 107 N/cm2. By determining the values for different moduli, identify the properties of material and establish the relationship between them. What changes will...
Results obtained from a tension test on a bar of uniform cross section 10 mm x...
Results obtained from a tension test on a bar of uniform cross section 10 mm x 10 mm subjected to an axial pull of 8000 N were tabulated. The lateral dimensions of the bar were found to be changed to 9.9985 mm x 9.9985 mm while using a material having modulus of rigidity equal to 0.8 x 107 N/cm2. By determining the values for different moduli, identify the properties of material and establish the relationship between them. What changes will...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT