Question

In: Mechanical Engineering

Q1 The crank of a slider mechanism rotates clockwise at a constant speed of 300 rpm....

Q1 The crank of a slider mechanism rotates clockwise at a constant speed of 300 rpm. The crank is 15Q mm and the connecting rod is 60P mm long. Determine: a) Linear velocity and acceleration of the Slider. b) Angular velocity and angular acceleration of the connecting rod, at a crank angle of 45° from inner dead centre position.

Solutions

Expert Solution


Related Solutions

Hydraulic excavators always have a 4-bar linkage between the inverted crank-slider mechanism and the bucket. Find...
Hydraulic excavators always have a 4-bar linkage between the inverted crank-slider mechanism and the bucket. Find a picture from which you can determine if this 4-bar linkage is a triple rocker, a double crank, a double rocker, or a crank-rocke
In the planetary gear train shown in Figure Q2, the annulus A rotates at 300 rpm...
In the planetary gear train shown in Figure Q2, the annulus A rotates at 300 rpm about the axis of fixed wheel S which has 80 teeth. The armed spider (arm) is driven at 180 rpm. The annulus is connected to input shaft whereas the arm is connected to the output shaft. If the efficiency of gear system is 98% and input torque is 100 Nm, identify the following information regarding these problems (i) The number of teeth on planet...
5. A shaft rotates at a rate of 50 RPM against a constant torque of 2000...
5. A shaft rotates at a rate of 50 RPM against a constant torque of 2000 N.m. Calculate: a. The power required to rotate the shaft. b. The work required to rotate the shaft through 150 revolutions.
14. An engine runs at a constant load at a speed of 480 r.p.m. The crank...
14. An engine runs at a constant load at a speed of 480 r.p.m. The crank effort diagram is drawn to a scale 1 mm = 200 N-m torque and 1 mm = 3.6º crank angle. The areas of the diagram above and below the mean torque line in sq mm are in the following order: + 110, – 132, + 153, – 166, + 197, – 162 Design the flywheel if the total fluctuation of speed is not to...
An old-fashioned (vinyl) record rotates at a constant rate of 33 rpm. (a) What is its...
An old-fashioned (vinyl) record rotates at a constant rate of 33 rpm. (a) What is its angular speed in rad/s? rad/s (b) If the record has a radius of 9 cm, what is the linear speed of a point on its edge? m/s
The mechanism shown is for a transfer conveyor. The driving link rotates counterclockwise at a constant...
The mechanism shown is for a transfer conveyor. The driving link rotates counterclockwise at a constant rate of 25 rpm, and the box has a mass of 10 kg as shown. The mass of the driving link and the coupler are negligible. Conveyor friction is adequate to prevent box slipping in the position shown. The mass of the conveyor link is 15 kg and the center of gravity is at its midspan. The mass moment of inertia of the conveyor...
A wheel rotates with a constant angular acceleration of 3.0 rad/. If the angular speed of...
A wheel rotates with a constant angular acceleration of 3.0 rad/. If the angular speed of the wheel is 2 rad/s at t = 0, through what angular displacement does the wheel rotate in 2 s? 10 rad. 6 rad. 15 rad. 4 rad. 12 rad. Based on question number 3, through how many revolutions has the wheel turned during this time interval?   4 rev. 3 rev. 1.6 rev. 5 rev. 2 rev. Based on question number 3, what is...
Marla is running clockwise around a circular track. She runs at a constant speed of 2...
Marla is running clockwise around a circular track. She runs at a constant speed of 2 meters per second. She takes 46 seconds to complete one lap of the track. From her starting point, it takes her 12 seconds to reach the northernmost point of the track. Impose a coordinate system with units in meters, the center of the track at the origin, and the northernmost point on the positive y-axis. (Round your answers to two decimal places.) (a) Give...
A disk rotates with constant angular acceleration. The initial angular speed of the disk is 2?...
A disk rotates with constant angular acceleration. The initial angular speed of the disk is 2? rad/s. After the disk rotates through 20? radians, the angular speed is 3? rad/s. (a) What is the magnitude of the angular acceleration? rad/s2 (b) How much time did it take for the disk to rotate through 20? radians? s (c) What is the tangential acceleration of a point located at a distance of 3 cm from the center of the disk? m/s2
A helicopter has a rotor (radius R0) that rotates with constant angular speed ω. The helicopter...
A helicopter has a rotor (radius R0) that rotates with constant angular speed ω. The helicopter is accelerating vertically with constant acceleration A0, starting from rest. Using cylindrical coordinates a) Write the position vector of the tip of the rotor as a function of time. b) Find the velocity vector of the rotor tip as a function of time by taking the derivative of the previous result. c) Find the acceleration vector of the rotor tip as a function of...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT