Control DC Using PIC18f46k20 and MPLAB IDE v8.8, write a program that can 1. Start and...

Control DC Using PIC18f46k20 and MPLAB IDE v8.8, write a program that can

1. Start and Stop the motor

2.Vary The motor Speed

3.Change the direction of the motor rotation

4.Display motor speed in OLED screen

using c of MPLAB IDE v8.8

please test the code before posting

Solutions

Expert Solution

Manojponduru answered 1 year ago

Next > < Previous

Related Solutions

Write a Program using MPLAB IDE and XC8 compiler to do the followings: 1. When the...

Write a Program using MPLAB IDE and XC8 compiler to do the followings: 1. When the Program Starts it should send your Name and ID# to the Serial Port 2. Display the result on Tera Term. 3. Read PORTB buttons in an infinite loop (Main Loop which is the Read Buttons Loop), your program should not block when reading the Buttons except in De-bouncing.. But you need to de-bounce each button when pressed 3.1 If the user presses PORTB, RB0...

To develop a program for the PIC 16F84A using either MPLAB X IDE simulator software. T...

To develop a program for the PIC 16F84A using either MPLAB X IDE simulator software. T he PIC 16F84A has 8 LEDs connected to Port B. The program is to convert your student number (10 ASCII characters), taken in reverse order, one character at a time, to Gray code. Each converted character is to be displayed on 4 of the LEDs connected to Port B (B0 to B3) of the microcontroller. Further, each converted character will be displayed for 3...

Write a program By using ardino and h-bridg and dc motor No sensoer. VICHAEL start from...

Write a program By using ardino and h-bridg and dc motor No sensoer. VICHAEL start from A move some distance till point B than turn 90 degree than move some distance till C than turn 90 degree and move Tell point D than turn 90 degree and move till start point which is A As square moving (, starting from A and back to A)

In MPLAB write and compile (using the simulator) an assembly language program with the following functionality:...

In MPLAB write and compile (using the simulator) an assembly language program with the following functionality: Configures pin RA2 of the PIC24to be an output to control an attached LED. Configures pin RB13 of the PIC24 to be an input to read the value on an attached switch (this switch will connect to ground when pressed). Configures pin RB13 to use the internal pull-up resistor. After configuration, the LED will be "off" when the push-button is pressed, and "on" when...

Using ECLIPSE IDE Write a Java Program to play your version of the Texas Pick 3...

Using ECLIPSE IDE Write a Java Program to play your version of the Texas Pick 3 Lottery. You will need to include the provided code given below in your program. Task:The program will prompt for a number between 0 and 999. Your program will display the number of attempts it took for the entered number to match a randomly generated number. In the main() method, declare an int named myPick3choice. Create a prompt for myPick3choice as "Enter your Pick 3...

Speed control of motors (ac motors as well as dc motors) can be accomplished by using...

Speed control of motors (ac motors as well as dc motors) can be accomplished by using solid-state switching circuitry In one such method, a solid-state relay is activated using a switching signal generated by a microcomputer so as to turn on and off at high speed, the power into the motor drive circuit. Speed of the motor can be measured using a sensor such as tachometer or optical encoder. This signal is read by the microcomputer and is used to...

Write a program for hotel booking system using C++ Program Requirement 1. You can write any...

Write a program for hotel booking system using C++ Program Requirement 1. You can write any program based on the title assigned. 2. The program must fulfill ALL the requirements below. The requirements listed below are the MINIMUM requirement. Your program may extend beyond the requirements if needed. a) Create at least one (1) base class. b) Create at least two (2) derived classes that inherit from the base class created in 2(a). c) Create at least one (1) object...

C++ program using Eclipse IDE The C++ program should have concurrency. The C++ program should create...

C++ program using Eclipse IDE The C++ program should have concurrency. The C++ program should create 2 threads that will act as counters. One thread should count down from 5 to 0. Once that thread reaches 0, then a second thread should be used to count up to 20.

1.Write a C++ program using control structures, arrays, functions to calculate the number of dollars, quarters,...

1.Write a C++ program using control structures, arrays, functions to calculate the number of dollars, quarters, dimes, nickels, and pennies in a given amount of money. The input should be a floating-point value representing a decimal value. Example: 63.87 à 63 [dollars and 87 cents] should output 63 dollars, 3 quarters, 1 dime, 0 nickels, and 2 pennies. 2. In trigonometry the cosine function can be calculated using cos(x) = 1 – x 2 /2! + x 4 /4!- x...

Using Eclipse IDE Create a Java Program/Class named MonthNames that will display the Month names using...

Using Eclipse IDE Create a Java Program/Class named MonthNames that will display the Month names using an array. 1. Create an array of string named MONTHS and assign it the values "January" through "December". All 12 months need to be in the array with the first element being "January", then "February", etc. 2. Using a loop, prompt me to enter an int variable of 1-12 to display the Month of the Year. Once you have the value, the program needs...

Subjects