Question

In: Mechanical Engineering

You are to required to design a steam power cycle that must operate in the parameter...

You are to required to design a steam power cycle that must operate in the parameter space defined below. Final designs should be as close to the desired operating conditions as possible. You are to prepare an engineering report that clearly articulates your design and its analysis and should include, but is not limited to reporting on the following:

Thermodynamic principles and theory that describe the operation of your design

Analysis, including calculations of you design and the final cycle thermal efficiency, work output, required inputs and heat rejection requirements

Complete specification of the state of the working fluid at all points in the cycle

All system figures, T-s and P-v diagrams, correctly and adequately labelled such that all technical information is clearly conveyed

Max cycle thermal efficiency: 50%

Isentropic efficiency of the turbine: 80%

Isentropic efficiency of the pump: 75%

Max operating pressure: 15000kPa

Max quality at turbine exit: 0.95

Solutions

Expert Solution

samet mamat answered 1 year ago
Next > < Previous

Related Solutions

Design a steam power cycle that can achieve a cycle thermal efficiency of at least 40%...
Design a steam power cycle that can achieve a cycle thermal efficiency of at least 40% under the conditions that all turbines have isentropic efficiencies of 80% and all pumps have isentropic efficiencies of 65%. Prepare an engineering report describing your design. Your design report must include, but is not limited to, the following: 1. Discussion of various cycles attempted to meet the goal as well as the positive and negative aspects of your design. 2. System figures and T-s...
Design a steam power plant that works as an ideal Regenerative Rankine cycle with 2 closed...
Design a steam power plant that works as an ideal Regenerative Rankine cycle with 2 closed feedwater heaters cascaded backwards by selecting their extraction pressures to optimize cycle efficiency. The available steam conditions at the exit of the boiler are 3 MPa and 590 °C and the condenser pressure is 20 kPa. The steam flow rate at the inlet of the turbine is 80 kg/s. A T-s diagram for the cycle should be provided along with a table showing the...
A proposed steam power plant design consists of an ideal Rankine cycle with reheat and regeneration....
A proposed steam power plant design consists of an ideal Rankine cycle with reheat and regeneration. Steam enters Turbine 1 at P1 and T1 at the rate of m1 and exits at P2. A fraction (y') of the steam exiting Turbine 1 is diverted to an open feedwater heater while the remainder is reheated to T3 before entering Turbine 2. The condenser operates at P4. Saturated liquid exits the condenser and is fed to Pump 1. The outlet of Pump...
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated...
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated at 40 bar, and is exhausted to condenser at 0.07 bar. The condensate is pumped to pressure of 3.5 bar at which it is mixed with bleed steam from the turbine at 3.5 bar. The resulting water which is at saturated temperature is pumped to boiler. For the ideal cycle calculate, neglecting the feed pump work. 3 | P a g e I. The...
A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at...
A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at 3 MPa and “648” K and is condensed in the condenser at a pressure of 46 kPa. You are assigned on a project to improve the thermal efficiency of this plant. a) Draw the schematic of the plant and determine the thermal efficiency of the practical cycle assuming that the efficiencies of pump and turbine are 0.75 and 0.7, respectively. ( b) Draw a...
Consider a steam power plant operating on a simple ideal Rankine cycle in which the steam...
Consider a steam power plant operating on a simple ideal Rankine cycle in which the steam enters the turbine at 3 MPa and 350C and is condensed in the condenser at 75 kPa. Determine the thermal efficiency of this cycle and sketch an appropriately labeled T-s diagram. Also compare this thermal efficiency to that a Carnot heat engine operating between these same two limits. The change in enthalpy across the pump = work done by the pump: h2-h1= v1(P2– P1)
A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine...
A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine at 4 MPa and 500 C and leaves it at 50 kPa and 150 C. the water leaves the condenser as a saturated liquid and is subsequently displaced to the boiler by means of a pump at a temperature of 85 C, which is the isentrophic efficiency of the turbine?
A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6...
A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6 MPa at 700 ºC and the condenser at 10 kPa. Turbine has isentropic efficiency of 85% and pumps have isentropic efficiency of 90%. Steam is extracted from the turbine at 0.6 MPa to heat the feedwater in an open feedwater heater. Water leaves the open feedwater heater as saturated liquid. a) Draw the system with labels and show the ideal and the non-ideal cycle...
A Rankine cycle power plant is being developed to operate an irrigation system. In this power...
A Rankine cycle power plant is being developed to operate an irrigation system. In this power plant solar energy will be used to boil a low boiling point fluid within glazed flat plate solar collectors. The working fluid that has been selected is the commonly used refrigerant R 134a (1, 1, 1, 2 tetrafluoroethane), tabulated properties of which may be found in Tables A11, A12 and A13 at the rear of the prescribed text. The plates being used for the...
A Rankine cycle power plant is being developed to operate an irrigation system. In this power...
A Rankine cycle power plant is being developed to operate an irrigation system. In this power plant solar energy will be used to boil a low boiling point fluid within glazed flat plate solar collectors. The working fluid that has been selected is the commonly used refrigerant R 134a (1, 1, 1, 2 tetrafluoroethane), tabulated properties of which may be found in Tables A11, A12 and A13 at the rear of the prescribed text. The plates being used for the...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT