Question

In: Electrical Engineering

a) Draw the simplest circuit of the nMOS co-source amplifier and subtract the expression of the...

a) Draw the simplest circuit of the nMOS co-source amplifier and subtract the expression of the AC small signal voltage gain. (Note: Drain will have RD and Source will have degeneration resistance RS.)

b) Draw the small signal equivalent circuit of the circuit in question (a). Find the expression of the output impedance.

c) What is the Miller effect?

My English is weak, please have a clean spelling.

Solutions

Expert Solution

if you have doubt at any step please comment below


Related Solutions

Draw the circuit diagram of differential instrumentation amplifier and derive the expression of its output. Precisely...
Draw the circuit diagram of differential instrumentation amplifier and derive the expression of its output. Precisely control of temperature in many industries is critical to ensure the quality of the product. Discuss how you will use the instrumentation amplifier using transducer bridge to measure the temperature. Use block diagram to illustrate your concept.
Draw a circuit diagram of the differential amplifier with two Rcs.
Draw a circuit diagram of the differential amplifier with two Rcs.
Draw circuit schematic of DRAM and answer the following questions ▪ Why NMOS is used as...
Draw circuit schematic of DRAM and answer the following questions ▪ Why NMOS is used as a pass transistor in the conventional DRAM, not PMOS? ▪ Explain how capacitor retain data in DRAM ▪ If PMOS is used in DRAM instead of NMOS, suggest a method to increase its performance. Provide reason to support your answer
2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What...
2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What is the cutoff frequency of the amplifier in question (i) if we used an operational amplifier 741? (iii) What configuration (inverter or non-inverter) is most vulnerable to finite CMRR ( Common Mode Rejection Ratio )? (iv) Draw an instrumentation amplifier and calculate its literal equation of the gain
1) Draw the high frequency MOSFET equivalent circuit model. 2) Find an expression for the unity...
1) Draw the high frequency MOSFET equivalent circuit model. 2) Find an expression for the unity current gain frequency. 3) Calculate fT when tox= 5nm, gm=0.1 mA/V, W=5L=0.1 um. 4) What are the harmful effects of the gate resistance on the high frequency operation of MOSFET? 1)Draw a noise equivalent circuit ignoring the parasitic resistance contribution. Explain the components in the circuit. 2) What is the equivalent noise current attributed to the channel where its resistance is almost same with...
Write a literature survey about DC power supply circuit and audio amplifier circuit to preform a...
Write a literature survey about DC power supply circuit and audio amplifier circuit to preform a speaker?
Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that...
Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that clamps the positive peaks to −4V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. List any constraints that should be observed in selecting component values. Be sure to label the terminals across which the clamped output waveform vo(t) appears.
Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that...
Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that it is just oscillating wildly. List the first three things to check to understand what is causing the oscillation.
1. the use of Amplifier Loading in a circuit.? 2. the DC operation of a BJT...
1. the use of Amplifier Loading in a circuit.? 2. the DC operation of a BJT using an equivalent model in terms of base current (master) and output current (slave) loops.
How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it...
How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it on multisim.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT