An engineer at a microcircuit factory will inspect a batch of silicon wafers to try to...

An engineer at a microcircuit factory will inspect a batch of silicon wafers to try to find defects. Assume that there are four defective integrated circuits in a container containing twenty wafers. For that inspection two random wafers are selected. Calculate the probability that:
a) None of them have defects
b) At least one of the two has no defects.

Expert Solution

Solution: Here concept of probability is used.

milcah answered 1 year ago

One integrated circuit design calls for the diffusion of arsenic into silicon wafers; the background concentration...

One integrated circuit design calls for the diffusion of arsenic into silicon wafers; the background concentration of As in Si is 2.5 × 1020 atoms/m3. The predeposition heat treatment is to be conducted at 1000°C for 45 minutes, with a constant surface concentration of 8 × 1026 As atoms/m3. At a drive-in temperature of 1100°C, determine the diffusion time required for a junction depth of 1.2 μm. For this system, values of Qd and D0 are 4.10 eV and 2.29...

Which are the three orientations of silicon wafers most commonly employed in micromachining? Arrange them in...

Which are the three orientations of silicon wafers most commonly employed in micromachining? Arrange them in order of most common usage and briefly describe their benefits and drawbacks.

A new process has been developed for applying photoresist to 125-mm silicon wafers used in manufacturing...

A new process has been developed for applying photoresist to 125-mm silicon wafers used in manufacturing integrated circuits. Ten wafers were tested, and the following photoresist thickness measurements (in angstroms x1000) were observed: 13.3987, 13.3957, 13.3902, 13.4015, 13.4001, 13.3918, 13.3965, 13.3925, 13.3946, and 13.4002. (a) Test the hypothesis that mean thickness is 13.4 x 1000Å. Use = 0.05 and assume a two sided alternative. (b) Find a 99% two-sided confidence interval on mean photoresist thickness. Assume that thickness is normally...

Engineer Johnson was employed to inspect an aged vacant building and prepare a report on its...

Engineer Johnson was employed to inspect an aged vacant building and prepare a report on its structural condition before sale. He found some structural defects which, if not repaired, might lead to collapse of the building. He then advised his client to carry out the necessary repair works immediately. The client ignored the advice. In an email to Engineer Johnson, the client wrote, “…… I pay for your service. The content of the report is my privileged information. You should...

An engineer is responsible for monitoring the quality of a batch of 1000 ohm resistors. To...

An engineer is responsible for monitoring the quality of a batch of 1000 ohm resistors. To do so, the engineer must accurately measure the resistance of a number of resistors within the batch, selected at random. The results obtained are shown below for samples 1 to 30. 1006, 1006, 978, 965, 988, 973, 1011, 1007, 935, 1045, 1001, 974, 987, 966, 1013, 960, 976, 954, 1004, 975, 1014, 955, 973, 993, 1023, 992, 981, 991, 1013 and 998. (a) Determine...

An engineer in charge of the design of a plant must choose either a batch or...

An engineer in charge of the design of a plant must choose either a batch or a continuous system. The batch system offers a lower initial outlay but, owing to high labor requirements, exhibits a higher operating cost. The cash flows relevant to this problem have been estimated as follows: year 0 year 1-10 (after tax) discounted cash flow rate of return net present worth at 12% batch system -$20,000 $5,600/year 23% $14,000 continuous system -$30,000 $7,650/year 20% $17,600 Check...

cost value pricing Must show work CVP Question Catalonia Company (CC) makes silicon wafers that its...

cost value pricing Must show work CVP Question Catalonia Company (CC) makes silicon wafers that its salespeople sell B-to-B for $100/wafer. All salespeople get a commission equal to 10% of the revenue from the wafers they sell, and in addition, the salespeople receive a base salary of $40,000 per person. In 2017, CC had 10 sales people, and its total sales revenue was $10,000,000. The manufacturing facility used to make the wafers has a fixed cost of $2,000,000, and a...

A television factory knows that 2% of their televisions are defective. In a batch of 100...

A television factory knows that 2% of their televisions are defective. In a batch of 100 new televisions, 4 of them are inspected at random. What is the probability that 1 of them will be defective? What is the probability that they all turn out to be defective?

The insurance cost for a large factory would be considered a: Multiple Choice unit-level cost. batch-level...

The insurance cost for a large factory would be considered a: Multiple Choice unit-level cost. batch-level cost. product-level cost. facility-level cost.

You’re a quality control engineer for Norman’s fourth largest cracker factory, and you plan to implement...

You’re a quality control engineer for Norman’s fourth largest cracker factory, and you plan to implement some process changes if you conclude that the mean weight of a 32 ounce box of saltine crackers is less than 32 ounces. Based on a sample of 15 boxes, you found an average and standard deviation of cracker box weight of 31.6 ounces and 1.2 ounces, respectively. a. Draw conclusions with the critical value approach at 99% confidence. b. What is the probability...

Question