Question

In: Electrical Engineering

A solar cell fabricated with a p-n junction has an open circuit voltage of 0.6V and...

A solar cell fabricated with a p-n junction has an open circuit voltage of 0.6V and a short circuit current of 20mA/cm2when exposed to a solar insolation of 1000 W/m2, and has a form factor FF=0.7

  1. Draw the current-voltage characteristic of this device, making sure to identify the Voc and Isc, and the point where the maximum power is generated.
  2. What is the efficiency of this cell?
  3. Suppose you can improve the manufacturing process of the cell so that the carrier life time is increased by 4 times. What will happen to the Voc and Isc of the cell? Draw how the current voltage characteristic will change.
  4. If the solar insolation of 1000 W/m2 is constant for 8 hours per day and then is zero for 16 hours per day what is the capacity factor of this cell? How much electrical energy will it produce in a day?

Solutions

Expert Solution


Related Solutions

1. Why don’t the short circuit and open circuit voltage produce power in a p-n cell?...
1. Why don’t the short circuit and open circuit voltage produce power in a p-n cell? 2. The power supplied by a solar cell is proportional to its surface area. Using the flux of solar energy under AM1 conditions, estimate the power a 1-cm2 solar cell will yield. State explicitly any assumption you make.
Explain how a p - n junction works like a solar cell.
Explain how a p - n junction works like a solar cell.
Q. Consider a silicon p-n junction solar cell of area 4 cm2. If the doping of...
Q. Consider a silicon p-n junction solar cell of area 4 cm2. If the doping of the solar cell are NA = 1.0x1016cm-3 and ND = 1.5x1019 cm-3 and given τn = 10 μs, τp = 0.5 μs, Dn = 9.3 cm2 /s, Dp = 2.5 cm2 /s and IL = 95 mA, (a) calculate and plot the I-V characteristics of the solar cell, (b) calculate the open-circuit voltage and (c) determine the maximum output power of the solar cell,...
condidering a forward bias n-p junction and reverse bias n-p junction, which one produces a rectifying...
condidering a forward bias n-p junction and reverse bias n-p junction, which one produces a rectifying action? explain how it produces the rectifying action
Define the limitations in the operation conditions of a p-n junction.
Define the limitations in the operation conditions of a p-n junction.
what is the short circuit current (Isc) and open circuit voltage (Voc) and how can I...
what is the short circuit current (Isc) and open circuit voltage (Voc) and how can I obtain those value from a I-V curve?
A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of...
A single-phase transformer of 3 kVA, 60 Hz, has a voltage ratio on open circuit of 240 / 120 V. The primary and secondary resistances are 0.25 Ω and 0.05 Ω respectively, the corresponding leakage reactance being 0.75 Ω and 0.18 Ω. The transformer delivers current to the load at a 0.9 power factor lagging. Determine the voltage across the load.                                                                   Determine the power dissipated by the load.                                                          Determine percentage voltage regulation referred to the secondary...
Calculate the cell voltage for the following reaction at 25o C:                                 &n
Calculate the cell voltage for the following reaction at 25o C:                                     2 Cr3+ (aqueous; 0.010 M) + H2 (gas at 1 atm)                                     è 2 Cr2+ (aqueous; 0.050 M) + 2H+ (aqueous; pH = 2.50) The Eo for the reaction Cr3+ (aq) + e- ==è Cr2+ (aq) is - 0.40 V vs. the standard hydrogen half-cell.
Consider a Si p-n junction connected p-type and n-type semiconductors each doped 1017 /cm3 concentration, in...
Consider a Si p-n junction connected p-type and n-type semiconductors each doped 1017 /cm3 concentration, in temperature 50K, 350K, 650K Suppose occur energy state of conduction band quantization due to the junction make very small. If Si p-n junction has only three DOS(density of state) in conduction band and valence band, Discuss band diagrams and I-V curve.
Explain how a p-n junction can act as an LED, and if configured correctly as a...
Explain how a p-n junction can act as an LED, and if configured correctly as a laser. (What are the requirements for it to act as a laser?)
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT