Topic: Agitation A flat-blade turbine agitator with disk having six blade is installed in a tank....

Topic: Agitation

A flat-blade turbine agitator with disk having six blade is installed in a tank. The tank diameter (D_t) is 1.83 m, the turbine diameter (D_i) is 0.61 m and the width (w) is 0.122 mm. The tank contains four baffles, each having width (J) of 0.15 mm. The turbine operate (N) at 90 rpm and the liquid in tank has a viscosity (u) of 10 cP and a density (p) of 929 kg/m³. It is desired to design a small pilot unit with a vessel volume (V) of 2.0 L so that effects of various process variables on the system can be studied in the laboratory. The rate of the mass transfer appear to be important in this system so the scale-down should be on this basis. Design the new system specifying sizes, rpm and power.

Include all calculations and graphs if possible . Thank you.

Expert Solution

Thank you.

Upvote please.

samet mamat answered 1 year ago

Investigate the 'turbine blade (for jet engine) making process' Hint: Turbine blade is made of superalloy....

Investigate the 'turbine blade (for jet engine) making process' Hint: Turbine blade is made of superalloy. Recently, it shows the single crystalline structure. Format: Format is the same with previous homework. A4 up to 4-5 page. Photo and figures are welcome. References should be written.

what is the heat treatment procces for the aircraft turbine blade ?with steps

The rotor of a kaplan turbine is 2.8m in dia. at the blade tips and 0.9m...

The rotor of a kaplan turbine is 2.8m in dia. at the blade tips and 0.9m at the hub. Its speed of rotation is 110r/min. Water enters the rotor without shock, making an angle of 37° to the axial direction at the mean dia and rotor has a blade exit angle of 58° to the axial direction at the mean diameter. The available pressure head is 6.5m .Determine 1) the inlet angle of the rotor blades at the mean dia....

An airfoil profile to be used on a wind turbine blade is tested in a wind...

An airfoil profile to be used on a wind turbine blade is tested in a wind tunnel. The prototype (full-scale) airfoil section has a chord length of 2m and moves at 50 m/s relative to the wind, the wind tunnel model has a chord length of 0.4m. The temperature for the model test is the same as for prototype operation. (a) What criterion should be used to obtain dynamic similarity in the experiment? (Write out the criterion in an equation.)...

consider the turbine blade tip available in the laboratory of University and discuss the needs of...

consider the turbine blade tip available in the laboratory of University and discuss the needs of cooling technology specially specially to be used for the blood tree using photo and 77 develop a mathematical model and show the effect of wearing the dimensions of the blood type on its performance discuss also the effect of film cooling and unsteady turbulence something pulling film hall and gauge arrangement to be made and enhancement in the cooling techniques which we can implement...

who to design ram air turbine blade by BEM-based approach

A flat circular loop having six turns and radius 9.0 cm is placed on a horizontal...

A flat circular loop having six turns and radius 9.0 cm is placed on a horizontal surface. The resistance of the wire is 25 Ohms. A 9V battery is attached to the wire, allowing for the flow of electrons. a) What is the magnitude and direction of the magnetic field? Assume the horizontal surface is defined by the xy – plane b) If the wire shorts out (causing the current to stop flowing) in 50ms, what is the induced emf?

A 3-blade wind turbine with a diameter of 16 m spins at 35 rpm at a...

A 3-blade wind turbine with a diameter of 16 m spins at 35 rpm at a 5000 m elevation where the average wind speed is 30 km/hr. The atmospheric pressure and temperature at that location are 98 kPa and -10 oC, respectively. There is a rotating wake behind the turbine. Neglecting the frictional drag, calculate the maximum power coefficient and maximum power.

A turbine blade of solution annealed INCOLOY alloy 800 is 18 in long and operates at...

A turbine blade of solution annealed INCOLOY alloy 800 is 18 in long and operates at 1400 degrees Fahrenheit. If the tip clearance is 0.2 in and centrifugal forces induce an average longitudinal stress of 10 ksi. After how many hours is expected the blade to interfere with the turbine stator due to creep?

You plot a θ vs time graph of a wind turbine blade and note a linear...

You plot a θ vs time graph of a wind turbine blade and note a linear relationship. The slope of the line is 1.45 rad/s. Which of the following applies? a. The angular acceleration is greater than 1 rad/s^2. b. The blade is rotating at a constant angular speed. c. The blade's kinetic energy is increasing. d. The blade's angular speed is decreasing.

Question