A pentagonal prism with side of base 30 mm and axis 60 mm long is resting/laying on its base on HP such that one of...

1. A pentagonal prism with side of base 30 mm and axis 60 mm long is resting/laying on its base on HP such that one of its base edge is parallel to VP and 15 mm in front of it. Draw the projections of the prism.

2. A hexagonal prism with side of base 30 mm and axis 50 mnm long is resting/laying on its base on VP such that one of its base edge is parallel to HP and 20 mm above it. Draw the projections of the prism.

3. A pentagonal pyramid of side base 30mm and axis 50mm long is laying on its base on VP and an edge of its base is perpendicular to HP. Its axis is 40 mm above HP. Draw the projections of the pyramid.

Expert Solution

Amanda K answered 2 years ago

Engineering graphic. 1. A circle of 50 mm diameter is resting on HP on end...

Engineering graphic. 1. A circle of 50 mm diameter is resting on HP on end A of it’s diameter AC which is 30 degree inclined to HP and makes 45 degree inclination to VP. Draw its projections

A 60º quartz prism is cut with its faces parallel to the optic axis. The refractive...

A 60º quartz prism is cut with its faces parallel to the optic axis. The refractive indices for ordinary and extraordinary rays are 1.5422 and 1.5533 respectively. Assume that the wavelength of the light used is 5890 Å. Calculate the angle of minimum deviation for yellow light for ordinary and extraordinary rays.

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with...

A three phase 30 hp 460 volt 60 hz, 1770 rpm design B induction motor with class F insulation and service factor of 1.0 is operating at rated shaft load in a 40 degree C environment and has an expected 20 yr life. A maintenance check shows line to line voltages to be 449.2 V, 431.3 V and 462.4 volts. The percent unbalanced voltage for this motor is: the expected temperature rise equals? The expected insulation life equals? the rerating...

A base for an airport runway, 100 m wide, 2000 m long and 500 mm thick,...

A base for an airport runway, 100 m wide, 2000 m long and 500 mm thick, is to be constructed out of a clayey sand excavated from a nearby borrow pit, where the in situ water content is 6%. This soil is being transported in trucks having a capacity of 8 m 3 , where each load weighs 13200 kg. In the subbase course, the soil will be placed at a water content of 14.2% to a dry density of...

A 30 m long pipe with an outside diameter of 75 mm is used to deliver...

A 30 m long pipe with an outside diameter of 75 mm is used to deliver steam at a rate of 2000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be given insulation with thermal conductivity of 0.2 W / (m K) so that the vapor quality only slightly decreases to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore...

One mole of solid MgO occupies 22.37 mm on a side. Calculate the density of MgO...

One mole of solid MgO occupies 22.37 mm on a side. Calculate the density of MgO ( in g/cm^3) ---Steps please

In a thought experiment, a cubic box of side length 0.01 mm contains three particles. One...

In a thought experiment, a cubic box of side length 0.01 mm contains three particles. One particle moves just in the x-direction, colliding elastically with the left and right walls of the cube. The second atom moves just in the y-direction, colliding elastically with the front and back walls of the cube. The third atom moves just in the z-direction, colliding elastically with the top and bottom walls of the cube. All three atoms have speed 500 m/s and mass...

Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and...

Consider a W30x99 beam (Fy = 60 ksi) that is simply supported, 30 ft. long, and subjected to a point load at the midspan. The point service load consists of 60% live load and 40% dead load. Lateral supports exist at the ends only. Design code to comply with: 2016 AISC LRFD. (a) Determine the maximum point service load P for strong-axis bending assuming Cb = 1.0. (b) Redetermine the maximum point service load P for strong-axis bending considering proper...

One long wire carries current 16.0 A to the left along the x axis. A second...

One long wire carries current 16.0 A to the left along the x axis. A second long wire carries current 72.0 A to the right along the line (y = 0.280 m, z = 0). (a) Where in the plane of the two wires is the total magnetic field equal to zero? (b) A particle with a charge of ?2.00 µC is moving with a velocity of 150î Mm/s along the line (y = 0.100 m, z = 0). Calculate...

One long wire carries current 32.0 A to the left along the x axis. A second...

One long wire carries current 32.0 A to the left along the x axis. A second long wire carries current 68.0 A to the right along the line (y = 0.280 m, z = 0). a) (5 points) Where in the plane of the two wires is the total magnetic field equal to zero? b) (5 points) A particle with a charge of −2.00 µC is moving with a velocity of 150 î Mm/s along the line (y = 0.100...

Question