Question

In: Physics

Question (2) A cylindrical titanium road of diameter 15mm is subjected to a tensile load applied...

Question (2)
A cylindrical titanium road of diameter 15mm is subjected to a tensile load applied along the long axis. Young’s modulus of the metal is 115.7 GPa and Poisson’s is 0.321. Determine the magnitude of the load needed to produce a contraction in diameter of 5x10 to the power 3 mm if the deformation is elastic

Solutions

Expert Solution


Related Solutions

During the experiment a constant tensile load was applied to the sample, as described in Study...
During the experiment a constant tensile load was applied to the sample, as described in Study session 17.1. This caused the sample to extend. You measured the change in length of the sample over time, which enabled you to calculate the strain. In Question 2a you are asked to calculate the stress acting on parts of a sample at the beginning and end of an experiment similar to that in Week 17. The load applied in the experiment was 5.1...
finite element problem Tapered bar subjected to variable axial distributed load A Titanium tapered bar of...
finite element problem Tapered bar subjected to variable axial distributed load A Titanium tapered bar of 25 in. length has a variable cross-sectional area that decreases linearly from 20 in2 to 10 in2 . It is fixed at one end and subjected to an axial concentrated force F = 100 kip at the free end, as shown in the following figure. It’s also subjected to a linearly axial distributed load of variable intensity ?(?) = 0.1 (1 − ? ?...
Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load....
Question1) A motor shaft is subjected to 4 kN axial load and 2 kN radial load. shaft rotates 800 rpm and its roller bearing has lh=10000 hours working life.Choose the single row roller bearing .(define the diameter of shaft)(Can you assign it to the table pictures.)
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm...
Question 1 a) A cylindrical feedstock of length = 35.4 cm and diameter = 10 cm is subjected to turning using a high speed steel tool. For this tool, n and C values in the Taylor tool life equation are 0.125 and 70 m/min, respectively. The cost for hiring an operator and using the machine tool are $82 per hour. The tooling cost per edge of cutting is $5. Loading and unloading the part on to the machine takes about...
Question: A cylindrical rock sample with a diameter of 54 mm in the uniaxial compressive strength...
Question: A cylindrical rock sample with a diameter of 54 mm in the uniaxial compressive strength test It was broken by applying a force of 160.2 kN. Since the angle between the applied load direction and the breaking surface is 30 °, the stresses acting on the breaking surface; (a) Solve using the Mohr diagram (graphic method). (b) Solve by analytical method.
A horizontal force of P = 56kN is applied to joint C. Each pin has a diameter of 25 mm and is subjected to double she...
A horizontal force of P = 56kN is applied to joint C. Each pin has a diameter of 25 mm and is subjected to double shear. Determine the average shear stress developed in pin Aof the truss. A horizontal force of P = 56kN is applied to joint C. Each pin has a diameter of 25 mm and is subjected to double shear. Determine the average shear stress developed in pin Aof the truss.
A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried...
A cylindrical shaped potato with length 2 cm and a diameter of 0.5 cm was dried at a temperature of 65 o C in a convective oven for 24 h, if the surface temperature of the potato remained at 62 o C throughout the drying operation, describe the different changes that occurs during the constant and falling rate periods
A closed rigid cylindrical vessel (internal diameter = 2 ft and internal height = 10 ft)...
A closed rigid cylindrical vessel (internal diameter = 2 ft and internal height = 10 ft) has R-134a at x = 0.95 and 40 oF. The vessel is heated up to 100 oF. Assume that heat loss from the vessel is negligible. Kinetic and potential effects are negligible. Determine 1) the final pressure in psi [lbf/in2], 2) the mass of R-134a in lbm, 3) the heat transfer in Btu for this process and discuss its direction (if the heat is...
A 1-m-diameter cylindrical mass, M, is connected to a 2-m- wide rectangular gate as shown in Fig. P2.143.
A 1-m-diameter cylindrical mass, M, is connected to a 2-m- wide rectangular gate as shown in Fig. P2.143. The gate is to open when the water level, h, drops below 2.5 m. Determine the required value for M. Neglect friction at the gate hinge and the pulley.
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel...
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel tube. The tube is 10 mm thick with an outside diameter of 50 mm. The bar and the tube are initially 1 m long and are rigidly fastened together at each end. Calculate the stresses in the two materials when the temperature is raised by 80 0C.                                2.2       If the composite bar is then subjected to an axial tensile load of 60 kN, find...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT