Question

In: Mechanical Engineering

Problem 2. Problem 1. An ideal Rankine Cycle with reheat uses water as the working fluid...

Problem 2.

Problem 1.

An ideal Rankine Cycle with reheat uses water as the working fluid with a flow rate of 0.15 kg/s.
At the inlet of the turbine (state 1) the water is a superheated vapor at 475ºC and 11 MPa.
The pressure at the exit of the first stage of the turbine is 0.9 MPa.
The reheat temperature (state 3) is also  475ºC.  
The condenser pressure is 8 kPa, and the water exits as a saturated liquid

Find: (a) The heat addition to the cycle, (b) the consumption rate of U-235 to maintain the heat addition if this is a nuclear power plant, and (c) the consumption rate of natural gas to maintain the cycle

Problem 2.

Re-do problem 1 using an isentropic efficiency of 80% for both stages of the turbine and the pump

Solutions

Expert Solution


Related Solutions

An ideal Rankine Cycle with reheat uses water as the working fluid with a flow rate...
An ideal Rankine Cycle with reheat uses water as the working fluid with a flow rate of 0.15 kg/s. At the inlet of the turbine (state 1) the water is a superheated vapor at 475ºC and 11 MPa. The pressure at the exit of the first stage of the turbine is 0.9 MPa. The reheat temperature (state 3) is also  475ºC.   The condenser pressure is 8 kPa, and the water exits as a saturated liquid Find: (a) The heat addition to...
An ideal Rankine Cycle with reheat uses water as the working fluid with a flow rate...
An ideal Rankine Cycle with reheat uses water as the working fluid with a flow rate of 0.15 kg/s. At the inlet of the turbine (state 1) the water is a superheated vapor at 475ºC and 11 MPa. The pressure at the exit of the first stage of the turbine is 0.9 MPa. The reheat temperature (state 3) is also  475ºC.   The condenser pressure is 8 kPa, and the water exits as a saturated liquid Find: (a) The heat addition to...
A Rankine power cycle with reheat uses water as the working fluid. The inlet conditions of...
A Rankine power cycle with reheat uses water as the working fluid. The inlet conditions of the first stage turbine are 14MPa and 600oC. All the turbines are known to have isentropic efficiency of 85%, however the pump is assumed as an isentropic pump. If the maximum temperature is kept at 600oC and the condenser pressure is 6 kPa, by constructing a suitable plot, show that having more than 2 reheat stages is not practical. (Hint: Take at least three...
Steam is the working fluid in an ideal Rankine cycle with superheat and reheat. Steam enters...
Steam is the working fluid in an ideal Rankine cycle with superheat and reheat. Steam enters the high-pressure turbine at 8.0MPa, 480̊C, and expands to 0.6MPa. It is then reheatedto 450̊C before entering the low-pressure turbine where it expands to the condenser pressure of 10kPa. The net power output is 110MW. A closed feedwater heater (CFWH) which uses steam extracted fromthe low-pressure turbine at 0.5MP. The extracted steam leaves the CFWH as a saturated liquid and is then pumped up...
A reheat Rankine cycle operates with water as the working fluid. Steam enters the first turbine...
A reheat Rankine cycle operates with water as the working fluid. Steam enters the first turbine at 8 MPa and 450◦C and exits at 0.8 MPa. It is then reheated at 400◦C before entering the second turbine, where it exits at 10 kPa. If the amount of work into the pump is 8.04 kJ/kg and the net work per cycle produced is 1410.5 kJ/kg, determine the thermal efficiency. Assume no pressure losses in the condenser or the boiler.
Consider a simple ideal Rankine cycle which uses water as the working fluid. The net power...
Consider a simple ideal Rankine cycle which uses water as the working fluid. The net power of power plant is 220-MW. At the turbine inlet, steam is at 9 MPa and 560°C. The condenser pressure is 20 kPa. Determine the following values.   The temperature at the pump inlet. °CThe specific enthalpy at the pump inlet. kJ/kgThe specific volume at the pump inlet. m3/kgThe pump work. kJ/kgThe temperature at pump exit. °CThe specific entropy at turbine inlet. kJ/kg·KThe quality of steam...
Consider a simple ideal Rankine cycle which uses water as the working fluid. The boiler pressure...
Consider a simple ideal Rankine cycle which uses water as the working fluid. The boiler pressure is 6100 kPa and the condenser pressure is 30 kPa. At the turbine inlet, steam is at 480°C. The isentropic efficiency of the turbine is 92 percent. The pump losses are negligible and the water leaving the condenser is subcooled by 6.3°C. The boiler is sized for a mass flow rate of 20 kg/s. Determine the following values. The temperature at the pump inlet....
Water is the working fluid in an ideal Rankine cycle. Saturated vapor enters the turbine at...
Water is the working fluid in an ideal Rankine cycle. Saturated vapor enters the turbine at 16 MPa, and the condenser pressure is 8 kPa. The mass flow rate of steam entering the turbine is 50 kg/s. Determine: (a) the net power developed, in kW. (b) the rate of heat transfer to the steam passing through the boiler, in kW. (c) the percent thermal efficiency. (d) the mass flow rate of condenser cooling water, in kg/s, if the cooling water...
A simple ideal Rankine cycle with water as the working fluid operates between the pressure limits...
A simple ideal Rankine cycle with water as the working fluid operates between the pressure limits of 4 MPa in the boiler and 5 kPa in the condenser and a turbine inlet temperature of 700°C. The boiler is sized to provide a steam flow of 50 kg/s. Determine the power produced by the turbine and consumed by the pump. Use steam tables. Find the values of power produced by the turbine and consumed by the pump in kW
Consider an ideal Rankine cycle modified with the addition of a single reheat stage. The working...
Consider an ideal Rankine cycle modified with the addition of a single reheat stage. The working fluid is H20. The maximum pressure in the cycle is 10MPa, and the temperature of the steam exiting both the boiler and the reheater is 550°C. The pressure in the condenser is 10kPa. 1.Draw the T-s diagram for the following three cases. a) 4.5MPa (= 0.25Pmax + 2MPA) b) 2.5MPA (= 0.25Pmax) c) 0.5MPa (= 0.25Pmax - 2MPA) 2.Calculate the thermal efficiency for the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT