A 50 inch long belt is used to transmit power from a motor to a working...

A 50 inch long belt is used to transmit power from a motor to a working shaft. The two sheaves involved are both the same size, hence the belt is not being used to reduce or increase speed or torque, but simply to “couple” two shafts. The motor’s rated power is 50 hp and the required service factor is 1.25. The motor speed is 1160 rpm and the sheave diameters are 7.9”. How many 5V belts are required here? What is the number of belts required?

Expert Solution

samet mamat answered 1 year ago

Why are superconductors not used to transmit power? If superconductors were available at the time of...

Why are superconductors not used to transmit power? If superconductors were available at the time of Edison and Tesla, would Edison have won the energy battle? What would change if superconductors could be used economically in our electrical grid?

Describe the techniques used to transmit and distribute HVDC power. Please type answer.

a. A shaft is used to transmit power. What does this mean? b. Explain the general...

a. A shaft is used to transmit power. What does this mean? b. Explain the general process of choosing a material for a shaft. c. Discuss the considerations that must be made when selecting the layout of a shaft.

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a...

A motor apply power 10-hp split-phase motor speed at 1700 rpm is used to drive a rotary pump, which operates 24 hours per day. An engineer has specified a 7-in small sheave, an 10-in large sheave, and three C112 belts. The service factor of 1.2 was augmented by 0.1 because of the continuous-duty requirement. Analyze the drive and estimate the belt life in passes and hours.

A moving belt system is to be used to fransfer lubricant from a sump to the...

A moving belt system is to be used to fransfer lubricant from a sump to the point of application. The working length of the belt is assumed to be straight and to be running parallel to a stationary metal surface. The belt speed is 200 mm/s, the perpendicular distance between the belt and the metal surface is S mm, and the belt is 500 mm wide. The lubricant is an oil, having an absolute viscosity of 0.007 Ns/m2• Estimate the...

High-voltage lines transmit needed power from energy providers to homes and businesses, but exposure to the...

High-voltage lines transmit needed power from energy providers to homes and businesses, but exposure to the electric fields from power lines may have undesired effects. Research and assess the effects of exposure to high-voltage lines on human health.

How long will it take to transmit a GB file from one VSAT to another using...

How long will it take to transmit a GB file from one VSAT to another using a hub as shown in Figure below? Assume that the uplink is 1 Mbps, the downlink is 7 Mbps, and circuit switching is used with 1.2 sec circuit setup time.

Q1.How long will it take to transmit a 1-GB file from one VSAT to another using...

Q1.How long will it take to transmit a 1-GB file from one VSAT to another using a hub as shown in Figure below? Assume that the uplink is 1 Mbps, the downlink is 7 Mbps, and circuit switching is used with 1.2 sec circuit setup time. Q2. Calculate the transmit time in the previous problem if packet switching is used instead. Assume that the packet size is 64 KB, the switching delay in the satellite and hub is 10 microseconds,...

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a...

A 150-mm-wide polyamide F-1 flat belt is used to connect a 50-mm-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 2.7 m. The angular speed of the small pulley is 1750 rev/min as it delivers 1.5 kW. The service is such that a service factor Ks of 1.25 is appropriate. (a) Estimate the centrifugal tension Fc and the torque T. (b) Estimate the allowable F1, F2, and Fi. c) Check the...

A 10-pole induction motor is fed with a 230 V, 50 Hz supply used to drive...

A 10-pole induction motor is fed with a 230 V, 50 Hz supply used to drive multiple loads with 0.85 power factor. Answer the following. i. State 3 types of starting circuit. ii. Calculate angular speed (Ns) in rpm and slip (S). Given rotor speed 550 rpm. iii. Calculate the efficiency of the motor. Given output power 1000 W, copper loss 10 W, core loss 5 W and rotational losses 80 W.

Question