Question

In: Mechanical Engineering

Methane is burned with air and the exhaust products are measured (on a dry, volumetric basis)...

Methane is burned with air and the exhaust products are measured (on a dry, volumetric basis) to be 4.8% CO2, 0.12% CO, 12.25% O2, and balance N2. Determine (a) the air-tofuel ratio (mass based) (5 points), (b) equivalence ratio (5 points) (c) the percent theoretical air (%) (5 points), (d) the percent excess air (%) (5 points), and (e) exhaust dew point (°C) if the exhaust is at 1 atm (5 points). (25 points)

Solutions

Expert Solution


Related Solutions

Methane is burned with air and the exhaust products are measured (on a dry, volumetric basis)...
Methane is burned with air and the exhaust products are measured (on a dry, volumetric basis) to be 4.8% CO2, 0.12% CO, 12.25% O2, and balance N2. Determine (a) the air-tofuel ratio (mass based) (5 points), (b) equivalence ratio (5 points) (c) the percent theoretical air (%) (5 points), (d) the percent excess air (%) (5 points), and (e) exhaust dew point (°C) if the exhaust is at 1 atm (5 points). (25 points)
9.77 Methane is burned with 25% excess air in a continuous adiabatic reactor. The methane enters...
9.77 Methane is burned with 25% excess air in a continuous adiabatic reactor. The methane enters the reactor at 25 C and 1.10 atm at a rate of 550 L/s, and the entering air is at 150 C and 1.1 atm. Combustion in the reactor is complete, and the reactor effluent gas emerges at 1.05 atm. a) Calculate the temperature and the degrees of superheat of the reactor effluent. (Consider water to be the only condensable species in the effluent)....
Exhaust gases having properties similar to dry air enter a thin-walled square duct exhaust stack at...
Exhaust gases having properties similar to dry air enter a thin-walled square duct exhaust stack at 500 ºC. The stack is made of galvanized iron and is 20 m tall and 0.25 m side. If the gas flow rate is 0.5 kg/s and the stack surface has the outside ambient temperature of 10 ºC estimate: a) the outlet temperature of the exhaust gas b) the heat transfer coefficient c) the rate of heat transfer d) the pressure drop
A propane burning engine is being evaluated and the exhaust gas collected on a dry basis...
A propane burning engine is being evaluated and the exhaust gas collected on a dry basis is 10.1% CO2, 1.1% CO, 4.7% O2 and 84.1% N2. During the test, 0.50 kg of fuel is burned and 1.73 m3 of exhaust gas (again dry) was collected at 15°C and 108 kPa. However, after the test someone questions whether it was really propane that was burned. Using the data above, specify what hydrocarbon was burned.
Methane at 25°C is burned in a boiler furnace with 10.0% excess air. The air enters...
Methane at 25°C is burned in a boiler furnace with 10.0% excess air. The air enters the burner at a temperature of 100°C. Ninety percent of the methane fed is consumed; the product gas is analyzed and found to contain 10.0 mol CO2 per 1 mol of CO. The exhaust gases exit the furnace at 400°C. Calculate the rate of heat transferred from the furnace, given that a molar flow rate of 100 mol/s CH4 is fed to the furnace.
A fuel gas containing methane and ethane is burned with air in a furnace, producing a...
A fuel gas containing methane and ethane is burned with air in a furnace, producing a stack gas at 300.°C and 105 kPa (absolute). You analyze the stack gas and find that it contains no unburned hydrocarbons, oxygen, or carbon monoxide. You also determine the dew-point temperature. (a) Estimate the range of possible dew-point temperatures by determining the dew points when the feed is either pure methane or pure ethane. (b) Estimate the fraction of the feed that is methane...
A fuel gas containing methane and ethane is burned with air in a furnace, producing a...
A fuel gas containing methane and ethane is burned with air in a furnace, producing a stack gas at 300 ° C and 105 kPa (absolute). You analyze the stack gas and find that it contains no unburned hydrocarbons, oxygen, or carbon monoxide. You also determine the dew-point temperature. (a) Estimate the range of possible dew-point temperatures by determining the dew points when the feed is either pure methane or pure ethane. (b) Estimate the fraction of the feed that...
Methane gas (CH4) is burned in a combustor with a given percentage of excess air. The...
Methane gas (CH4) is burned in a combustor with a given percentage of excess air. The pressure and temperature of both the air and fuel are 101 kPa and 298 K respectively. Assume that the mole fractions are 79% nitrogen and 21 % oxygen for air (use M=28.97 kg/kmol and R=0.287 kJ/kg-K) and that water is a vapor in the exhaust. Given the values below, determine the following: --Given Values-- m_fuel (kg) = 100 Excess Air = 25% a) Determine...
Methane is burning with minimum amount of air to form the stable products. The premixed methane-air...
Methane is burning with minimum amount of air to form the stable products. The premixed methane-air mixture is filled in a leak-proof spherical vessel at an initial pressure of 1 bar and 298 K. The vessel is well insulated to avoid thermal energy interaction with the surroundings.The combustible mixture is ignited at the centre of the vessel using an electrical spark. The energy added to the mixture for ignition is negligible. During the combustion process, the pressure of the combustion...
Methane is completely burned with 30% excess air, with 20% of the carbon transforming to CO....
Methane is completely burned with 30% excess air, with 20% of the carbon transforming to CO. a) What is the molar composition of the stack gas on a dry basis? b) Estimate the partial pressure of the CO in the stack gas if the barometer read 750 mmHg.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT