Question

In: Mechanical Engineering

Q1/ Why should you never set an electrified rod (welding unit on and rod is attached) down on a metal table?

 

Q1/ Why should you never set an electrified rod (welding unit on and rod is attached) down on a metal table?

 

A. To prevent overheating of the workpiece metal

B. To prevent condensation on the rod

C. To prevent oxides

D. To prevent an unexpected ignition of the arc

 

Q2 / What is the minimal level of shielding (welding mask) during stick welding?

 

A. 7

B. 5

C. 11

D. 8

 

Q3 / What is the code for the welding stick used?

 

A. 5013

B. 6013

C. 5011

D. 6011

 

Q4 / In stick welding how is the weld zone protected from contamination?

 

A. Flux

B. Gas shield

C. No protection is needed

D. Liquid flux

 

 

Solutions

Expert Solution

 


Related Solutions

Suppose you shuffle a deck of cards and set it down on the table. (a) What...
Suppose you shuffle a deck of cards and set it down on the table. (a) What is the probability that the top ten cards contain no aces? (There are four aces in the whole deck). (b) What is the probability that the top four cards are all the same suit? (There are four suits, and thirteen cards belonging to each suit). (c) What is the probability that the top four cards contain (exactly one) pair of the same card? (There...
Since the state of emergency is set, a metal rod leads 1200 J off a 400...
Since the state of emergency is set, a metal rod leads 1200 J off a 400 K reservoir to one with a temperature of 250 K for a certain amount time interval. Determine the entropy change before the hot reservoir; the cold reservoir; the metal rod and the whole system. Determine the change in entropy for each of the following processes: 1.0 kg of water at a temperature of 100◦C transfers to steam with the temperature 100◦C at constant pressure.1.0...
A block rests on a horizontal frictionless table. It is attached to a spring and set...
A block rests on a horizontal frictionless table. It is attached to a spring and set into motion. Consider what will happen to the frequency or period in each of the following situations. (increase, decrease, or stay the same) If the spring constant is cut in half (looser spring), the frequency will _______. If the spring constant is cut in half (looser spring), the period will _______. If the amplitude of the motion is doubled, the frequency will ______. If...
A rectangular loop is made by a metal bar that slides down a set of parallel...
A rectangular loop is made by a metal bar that slides down a set of parallel rails of negligible resistance in a vertical gravitational field g. The rails are connected together by a third rail of negligible resistance The resulting loop is in a uniform, vertical magnetic field B. First assume there is no friction between the bar and the rails. (a) Does the bar acquire a constant velocity and if so what is it? (b) Now take the coefficient...
How do decantation and filtration differ? Which should be faster? Why should you never place a...
How do decantation and filtration differ? Which should be faster? Why should you never place a hot object on the pan of balance ?
Should public policy dictate that some workers never be allowed to strike? Why or why not?
Should public policy dictate that some workers never be allowed to strike? Why or why not?
You have a vertical metal rod, a spring with one end closed and the other end...
You have a vertical metal rod, a spring with one end closed and the other end open so that it can slide down over the rod and then fly up when released, and a meter stick. The mass of the spring is 15g and its spring constant k is 6 N/m Your group decides to test the work-energy principle by stretching the spring a distance Dy = 30 cm, releasing it from rest and measuring how high it goes. Use...
Should the firm shut down in the short-run? Explain in detail why or why not.
Should the firm shut down in the short-run? Explain in detail why or why not.
Why should the payback method of analyzing capital purchases never be used as the sole basis...
Why should the payback method of analyzing capital purchases never be used as the sole basis for decision making?
Why should the payback method of analyzing capital purchases never be used as the sole basis...
Why should the payback method of analyzing capital purchases never be used as the sole basis for decision making?. Considering the amount of uncertainty and risk involved in capital budgeting, what is the point of applying any of the 4 analysis techniques to these decisions?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT