Question
In: Mechanical Engineering
C4h10 fuel is burned in the cylinder with 150% corporate air powered by SI engine. The...
C4h10 fuel is burned in the cylinder with 150% corporate air powered by SI engine. The temperature and pressure at the start of combustion are 650 K and 1900 kPa, respectively. The exhaust temperature leaving the cylinder at the end of combustion is 1100K. So what is the Fuel / Air ratio (FA)? C = 12 H = 1 N = 14 O = 16
Solutions
samet mamat answered 1 year agoRelated Solutions
Calculate air to fuel ratio by mass, for a four-cylinder SI engine running on i) gasoline...
Calculate air to fuel ratio by mass, for a four-cylinder SI
engine running on i) gasoline and ii) a mixture of 20% methanol and
80% gasoline both at stoichiometric conditions. Assume gasoline is
represented with C8H18 . Calculate any loss of power when
gasoline-methanol mixture is used and discuss your results.
1)A mixture of butene, C4H8 , and butane,C4H10, is burned in air to give CO2 and...
1)A mixture of butene, C4H8 , and butane,C4H10, is burned in air
to give CO2 and water. Suppose you burn 2.84 g of the mixture and
obtain 8.77 g of CO2 and 3.99 g of H2O . What are the mass
percentages of butene and butane in the mixture?
Mass percentage of butene = %
Mass percentage of butane = %
2)Copper metal can be prepared by roasting copper ore, which can
contain cuprite (Cu2S) and copper(II) sulfide.
Suppose an...
1. An aluminum air-cooled engine cylinder head for a single cylinder, 2-stroke engine is to be...
1. An aluminum air-cooled engine cylinder head for a
single cylinder, 2-stroke engine is to
be die-cast. The overall diameter of the cylinder head
is 101.6 mm. If the projected
plan area of the runners and gating system is 100 mm2
and the casting pressure is 10
MPa (1500 psi), what minimum locking force is required
for the die-casting machine in kN.
One kg of Methance (CH4) is burned with 200% theoretical air. What is the air fuel...
One kg of Methance (CH4) is burned with 200% theoretical air.
What is the air fuel ratio on a mass basis?
A fuel gas containing methane and ethane is burned with air in a furnace, producing a...
A fuel gas containing methane and ethane is burned with air in a
furnace, producing a stack gas at 300.°C and 105 kPa (absolute).
You analyze the stack gas and find that it contains no unburned
hydrocarbons, oxygen, or carbon monoxide. You also determine the
dew-point temperature.
(a) Estimate the range of possible dew-point temperatures by
determining the dew points when the feed is either pure methane or
pure ethane.
(b) Estimate the fraction of the feed that is methane...
A fuel gas containing methane and ethane is burned with air in a furnace, producing a...
A fuel gas containing methane and ethane is burned with air in a
furnace, producing a stack gas at 300 ° C and 105 kPa (absolute).
You analyze the stack gas and find that it contains no unburned
hydrocarbons, oxygen, or carbon monoxide. You also determine the
dew-point temperature.
(a) Estimate the range of possible dew-point temperatures by
determining the dew points when the feed is either pure methane or
pure ethane.
(b) Estimate the fraction of the feed that...
A piston-cylinder heat engine has five kilograms of air as the working fluid. Analyze this engine...
A piston-cylinder heat engine has five kilograms of air as the
working fluid. Analyze this engine as a Carnot engine and determine
the work of expansion and the amount of heat rejected in KJ
assuming constant specific heat at 300k. During the heat rejection,
the temperature is 300?. There is a temperature difference of 600
degrees in the engine. At the beginning of the heat rejection
process, the pressure is .2MPa and during heat addition the volume
doubles. Draw the...
(a) What is the best air/fuel ratio for an automobile engine? (b) If the mixture is...
(a) What is the best air/fuel ratio for an automobile engine?
(b) If the mixture is made leaner, what happens to the hydrocarbon
emissions? (c) If the fuel mixture is richer, how does this affect
NOx emissions
Ethane gas (C2H6) is burned with air. The fuel flow rate is 0.1 kg/s and the...
Ethane gas (C2H6) is burned with air. The
fuel flow rate is 0.1 kg/s and the air flowrate is 2.2 kg/s.
Ethane’s enthalpy of formation is -84,680 kJ/kmol. Determine:
The equivalence ratio
Ethane’s lower heating value by deriving it from enthalpy of
formation data.
The heat release rate, in kW.
The mass fraction of oxygen in the products.
The mass of CO2 emitted per 1000 hours of operation.
The mass of fuel burned per 1000 hours of operation.
The adiabatic...
Ethane (C2H6) is burned with air in a steady-flow combustor. The mass flow rate of fuel...
Ethane (C2H6) is burned with air in a
steady-flow combustor. The mass flow rate of fuel entering the
combustor is 0.57 kg/s and the equivalence ratio is 0.64. The fuel
enters at 25oC and the air enters at 500 K.
Determine:
The heat release rate, in kW.
The mass flow rate of air, in kg/s.
The mole fraction of O2 in the products.
The mass fraction of CO2 in the products.
The total mass of CO2 produced per year (365...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Tidewater Company uses the product cost concept of applying the cost-plus approach to product pricing. The...
- Create 5 short-term plan of technology projects that you can perform outside of an I.T. department...
- Derek plans to retire on his 65th birthday. However, he plans to work part-time until he...
- Toady and Froggy were running a vegan cafe together. The business was having financial difficulties.Betelguese, who...
- 1. The following questions concern Jesse Gelsinger who suffered from partial OTC. a. In the...
- Pittman Company is a small but growing manufacturer of telecommunications equipment. The company has no sales...
- TzeMay was one of the first women engineering students at ABC University. She graduated in 1995...
ADVERTISEMENT